annke DN41R User Manual Download Page 86

Page: 86 / 106

Digital Video Recorder User Manual

If you want to use the HDD even when the S.M.A.R.T. checking is failed, you can check the checkbox before the

Continue to use this disk when self-evaluation is failed

item.

Figure 11. 13 S.M.A.R.T Settings Interface

11.6 Detecting Bad Sector

Purpose:

You can detect the bad sector of the HDD to check the status of the HDD.

Steps:

Enter the HDD Detect interface.

Menu>HDD>HDD Detect

Click the Bad Sector Detection tab to enter the interface.

Select a HDD and click the

Detect

button to start detecting.

Figure 11. 14 Bad Sector Detecting

You can click the

Pause

button to pause the detection and click the

Resume

button to resume the detection.

If there is error information about the HDD, you can click the

Error Info

button to view the information.

Summary of Contents for DN41R











































































































Search results

Summary of Contents for DN41R

Reviews:

Related manuals for DN41R

Brands by name

Popular brands

annke DN41R, User Manual

Search results

Summary of Contents for DN41R

Reviews:

Related manuals for DN41R

Brands by name

Popular brands