annke DN41R User Manual Download Page 79

Page: 79 / 106

Digital Video Recorder User Manual

After the exporting is complete, click

to finish the packet export.

Up to 1M data can be exported each time.

10.4.3Checking Network Status

Purpose:

You can also check the network status and quick set the network parameters in this interface.

Steps:

Click Status on the right bottom of the page.

Figure 10. 23 Checking Network Status

If the network is normal the following message box pops out.

Figure 10. 24 Network Status Checking Result

If the message box pops out with other information instead of this one, you can click

Network

button to show

the quick setting interface of the network parameters.

Figure 10. 25 Network Parameters Configuration

10.4.4Checking Network Statistics

Purpose

You can check the network statistics to obtain the real-time information of the device.

Steps:

Enter the Network Statistics interface.

Menu > Maintenance> Net Detect

Click the

Network Stat.

tab to enter the Network Statistics menu.

Summary of Contents for DN41R











































































































Search results

Summary of Contents for DN41R

Reviews:

Related manuals for DN41R

Brands by name

Popular brands

annke DN41R, User Manual

Search results

Summary of Contents for DN41R

Reviews:

Related manuals for DN41R

Brands by name

Popular brands