manualshive.com logo in svg

Ankom Delta, Operator'S Manual

Share
Download
Ankom Delta Operator'S Manual Download Page 12

Operator’s Manual

 

 

 

 

 

 

 
pg. 12 

 

Rev 4/24/20 

 

Fiber Analysis Support Items 

The following support items are needed to perform the fiber analysis procedures: 

Item 

Recommended Product 

Electronic Balance with four-place readout

 

ANKOM #TB Balance Hardware 

ANKOM #TBS Balance Software 

Filter Bags

 

ANKOM #F57, #F58

 

Bag Holder (used for adding sample to an empty filter bag)

 

ANKOM #101.2

 

Heat Sealer for sealing the filter bags

 

ANKOM #1915 (120V), #1920 (220V)

 

Solvent Resistant Marker

 

ANKOM #F08

 

Desiccant Pouch

 

ANKOM #X45

 

Oven for drying (capable of maintaining 102°C ± 2°)

 

ANKOM #RD (120V), #RDI (220V)

 

Sample 

 

Spoon

 

 

Hot Water Heater 

ANKOM A02 

Water Filter Regulator Assembly 

 

Acid Detergent  

ANKOM FAD20CB cubitainer  

ANKOM FAD20 Concentrate 

ANKOM FAD20C, Concentrate-dry CTAB powder 

Neutral Detergent 

ANKOM FND20 cubitainer 

ANKOM FND20C Dry Concentrate 

Crude Fiber Acid 

ANKOM FCFA20CB cubitainer  

ANKOM FCFA20 Concentrate 

Crude Fiber Base 

ANKOM FCFB20CB cubitainer  

ANKOM FCFB20 Concentrate 

Alpha Amylase 

ANKOM FAA 

 

Analysis Options using the ANKOM

DELTA

 Automated Fiber Analyzer 

The ANKOM

DELTA

 Automated Fiber Analyzer can be configured to run ADF, NDF, and Crude Fiber analyses. The 

instrument will run with default digestion and rinse time settings unless you select the Custom analysis option. This 
option allows you to do ADF, NDF, or Crude Fiber analyses using custom digestion and rinse time settings. 

For maintenance purposes, the ANKOM

DELTA

 also flushes the chemical lines and valves after each run automatically. 

The following sections provide the information you will need to use and maintain the ANKOM

DELTA

 Automated Fiber 

Analyzer. 

 

 

 

 

 

Summary of Contents for Delta






































Reviews:

No comments

Brands by name

Popular brands

Load more brands