background image

WordClock-1 Assembly Guide 12/08/19 Version 1.2 
 
 

 

Page 8 

 

Warranty Terms and Conditions 

 
This software and hardware product is Copyright (C) 2019 by Mitchell Feig. It is exclusively 
distributed by OCEAN7 Watch Company d/b/a Angry Electrons 

(“AE”) All Rights Reserved. AE 

warrants that for a period of 90 days following delivery, AE kit parts will (a) perform in 
accordance with published specifications, and (b) will be free from defects in materials and 
workmanship. In the event an AE kit part does not meet this warranty, subject to the 
conditions set forth in these terms and conditions, AE

’s sole obligation will be, at its election, 

to repair or replace the AE kit part in question. AE may require return of the part for 
examination and replacement. Replacement will be completed at the sole discretion of AE, 
after examining the returned part. Correct assembly is the responsibility of the builder. AE will 
not attempt to correct non-working assembled kits. 
 

AE MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES 
OF MERCHANTABILITY, NON-INFRINGEMENT AND FITNESS FOR A PARTICULAR PURPOSE 
ARE HEREBY DISCLAIMED. IN NO EVENT WILL AE BE LIABLE FOR PUNITIVE, SPECIAL OR 
CONSEQUENTIAL DAMAGES, OR FOR AN AMOUNT IN EXCESS OF THE PURCHASE PRICE OF 
THE DEFECTIVE AE PART OR PRODUCT. 

 
 
 
 

 

Summary of Contents for WordClock-1











Reviews: