andrews LWHi49 Installation Manual Download

Page: 30 / 44

Item

Gas
Consumption (NET)

Hot Water Capacity

Capacity Range

Temperature Settings

25°C Rise

58°C Rise

G20
G31

28 L/min.

12 L/min.

2.0 - 37 L/min.

37 - 48, 50, 55, 60, 65, 70, 75, 80, 85°C

Maximum Performance

Minimum Performance

Specifi cation

External, Wall Hanging

Power Vented

Direct Ignition

2.0 bar

2.0 L/min.

60 cm(Height) x 35 cm(Width) x 24 cm(Depth)

26 kg

1.0 Litre

R 3/4”

220 - 240 VAC (50Hz)

Zincifi ed Steel Plate/Polyester Coating

Stainless Steel

Copper Sheeting, Copper Tubing

Flame Rod, Thermal Fuse, Pressure Relief Valve,

Lightning Protection Device (ZNR),

Overheat Prevention Device, Freezing Prevention Device,

Fan Rotation Detector

Anchoring Screws

Specifi cations

Performance

Item

Model Name

Type

Ignition

Minimum Pressure for Maximum fl ow

Minimum Flow Rate

Dimensions

Weight

Water Holding Capacity

Accessories

Installation
Air Supply/Exhaust

Connection Sizes

Power Supply

Materials

Water Inlet

Hot Water Outlet

Gas Inlet
Supply

Consumption

Casing

Flue Collar

Heat Exchanger

Safety Devices

WHiX49

LWHiX49

53.5 kW

4.35 kW

75.9W

Freeze Prevention 193W

75.9W

15.

Specifi cations

• Specifi cations may be changed without prior notice.
• The capacity may differ slightly, depending on the water pressure,

water supply, piping conditions, and water temperature.

Summary of Contents for LWHi49













































Search results

Summary of Contents for LWHi49

Reviews:

Related manuals for LWHi49

Brands by name

Popular brands

andrews LWHi49, Installation Manual

Search results

Summary of Contents for LWHi49

Reviews:

Related manuals for LWHi49

Brands by name

Popular brands