manualshive.com logo in svg

ANCA Motion AMD2000 3A, User Manual, Page: 92 / 189

Share
Download
ANCA Motion AMD2000 3A User Manual Download Page 92

AMD2000 Series - Servo Drive - User Manual 

 

 

92 

DS619-0-00-0019 - Rev 0

 

 

ANCA Motion 

 

10.1.13 

Configuring Wire-Saving UVW Motors 

 

Warning:  

This feature is recommended to be used only on braked axes, or axes that are unable to move.   

 

 

Description 

This document describes how to use UVW wire-saving encoders with AMD2000 drives to perform Field 
Orientation Initialisation (FOI).  It is important to note that the FOI alignment angle is latched during power-up. If 
you have downloaded code (or have entered into BOOTSTRAP mode), you MUST power cycle the drive.  Note 
that this feature is only supported on drive encoder channel 2. 
 
 

IDN 

Description 

P-0-006 / 32774 

Number of motor poles  

P-0-297 / 33065 

Field Orientation Initialisation Type 

P-0-312 / 33080 

Absolute Feedback Type 

P-0-579 / 33347 

UVW Hall Sensor Source 

 

Note on FOI and Index Pulse Offset Alignment 

As UVW wire-saving estimation of the field alignment only provides an estimate of optimal angle for Field 
Orientation Initialisation, this method is usually combined with index pulse offset alignment to maximise the 
output torque and efficiency of the motor.  See Section 

10.1.18 Field Orientation Initialisation

  for details of how to 

use these methods together. 

Procedure for setting up a UVW wire-saving Motor 

1.  Set UVW Hall Sensor Source (IDN 33347) to 3 (wire-saving Encoder 2). 
2.  Program the correct number of motor poles (IDN 32774). 
3.  Set Absolute Feedback Type (IDN 33080) to 2 (UVW hall sensors). 
4.  Set Field Orientation Initialisation Type (IDN 33065) to 3 (Absolute). 

 

Warning: 

Excessive movement (more than 30 electrical degrees) between drive power-up and when the 

drive firmware loads will result with an invalid field alignment, potentially resulting in axis run away.  This 
feature is recommended to be used only on braked axes, or axes that are unable to move.  If ever entering 
into the boot loader during drive operation, always power cycle the drive as the UVW signals will not be 
correct. 

 

 

10.1.14 

Digital Output 

Description 

The AMD2000 comes with 6 digital outputs (see Section 3.6).  These provide a powerful and flexible means of 
conveying information or making requests for actions external to the drive.  They are highly configurable, being 
able to provide useful information during normal operation, as well as under those conditions where the drive as 
an EtherCAT

4

  device is no longer in its operating (OP) state.  For example, an EtherCAT SAFEOP state might 

result from abnormal conditions related to loss of communication or software crashes, or the INIT and PREOP 
states can result from drive entering initialisation and start-up conditions. 

                                                           

4

 

EtherCAT® is a registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany

 

 

 

 

Summary of Contents for AMD2000 3A






























































































































































































Reviews:

No comments