background image

 

Evaluation Board User Guide

UG-012

One

 

Technology

 

Way

 

 

P.O.

 

Box

 

9106

 

 

Norwood,

 

MA

 

02062-9106,

 

U.S.A.

 

 

Tel:

 

781.329.4700

 

 

Fax:

 

781.461.3113

 

 

www.analog.com 

 

i

MEMS ADXL346 Inertial Sensor Evaluation System 

 

 

 
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT  
WARNING AND LEGAL TERMS AND CONDITIONS.

 

Rev. 0 | Page 1 of 12 

FEATURES 

Ultralow power 

ADXL346

 accelerometer  

Inertial sensor evaluation board 
Inertial sensor-specific satellite for evaluation 
Standard USB cable for power and communications 
PC-based graphical user interface (GUI) 
Separates DUT from controller for accurate environmental 

testing 

 

 

08

25

8-

00

1

 

Figure 1. Inertial Sensor Evaluation System 

 

 

GENERAL DESCRIPTION 

The 

i

MEMS® ADXL346 inertial sensor evaluation system  

is an easy-to-use evaluation tool targeting bench or desktop 
characterization of Analog Devices, Inc., inertial sensor 
products. The system consists of the inertial sensor evaluation 
board (ISEB), or main board, and a satellite board for any 
Analog Devices inertial sensor product. The ISEB connects 
directly to a PC via its USB, where the USB connection provides 
both power and communications to the board. The ISEB then 
connects to the satellite board through a ribbon cable. This 
cable allows the satellite to be easily manipulated for testing or 
for being separately placed into an environmental chamber for 
temperature or humidity testing. Separating the boards 
mitigates corruption of data due to the temperature and 
humidity effects of other components. 

The ISEB is a universal main board and is intended to be used 
with various satellites of Analog Devices inertial sensors, 
including analog and digital accelerometers, as well as gyroscopes. 
The different products are evaluated by means of separate GUIs 
that are customized for performance and characterization 
measurements relevant to the inertial sensor being evaluated.  

The EVAL-ADXL346Z-M system contains the ISEB and the 
EVAL-ADXL346Z-S satellite. Also included is a USB A to Mini-
B cable to connect the ISEB to a PC and an 18-inch, 20-pin 
ribbon cable to connect the ISEB to the satellite. A CD is also 
included with the necessary drivers and executables to use the 
system and to quickly begin evaluating the ADXL346. 

 

Summary of Contents for UG-012













Reviews: