manualshive.com logo in svg

Analog Devices SHARC ADSP-214 Series, Hardware Reference Manual, Page: 661 / 1192

Share
Download
Analog Devices SHARC ADSP-214 Series Hardware Reference Manual Download Page 661

ADSP-214xx SHARC Processor Hardware Reference

16-5 

Peripheral Timers

During the 

external event watchdog 

(EXT_CLK) mode, the period register 

is write-only. Therefore, the period buffer is used in this mode to insure 
high/low period value coherency. 

Pulse Width Register (TMxW).

 During the pulse width modulation 

(PWM_OUT), the width value is written into the timer width registers. 
Both width and period register values must be updated “on the fly” since 
the period and width (duty cycle) change simultaneously. To insure 
period and width value concurrency, a 32-bit period buffer and a 32-bit 
width buffer are used.

During the pulse width and period capture (WDTH_CAP) mode, both 
the period and width values are captured at the appropriate time. Since 
both the width and period registers are read-only in this mode, the exist-
ing 32-bit period and width buffers are used.

When the processor is in EXT_CLK mode, the width register is unused.

Read-Modify-Write

The traditional read-modify-write operation to enable/disable a peripheral 
is different for the timers. 

For more information, see “Peripheral Timer 

Registers” on page A-269.

Clocking

The fundamental timing clock of the peripheral timers is peripheral 
clock/4 (

PCLK

/4).

Functional Description

Each timer has one dedicated bidirectional chip signal, 

TIMERx

. The two 

timer signals are connected to the 14 digital peripheral interface (DPI) 

www.BDTIC.com/ADI

Summary of Contents for SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments