manualshive.com logo in svg

Analog Devices SHARC ADSP-214 Series, Hardware Reference Manual, Page: 470 / 1192

Share
Download
Analog Devices SHARC ADSP-214 Series Hardware Reference Manual Download Page 470

Functional Description

10-12

ADSP-214xx SHARC Processor Hardware Reference

Figure 10-2

 shows a block diagram of a serial port. Setting the 

SPTRAN

 bit 

enables the data buffer path, which, once activated, responds by shifting 
data in response to a frame sync at the rate of 

SPORTx_CLK

. An application 

program must use the correct serial port data buffers, according to the 
value of 

SPTRAN

 bit. The 

SPTRAN

 bit enables either the transmit data buffers 

for the transmission of A and B channel data, or it enables the receive data 
buffers for the reception of A and B channel data. Inactive data buffers are 
not used.

The processor’s SPORTs are not UARTs and cannot communicate with 
an RS-232 device or any other asynchronous communications protocol. 
One way to implement RS-232 compatible communication with the pro-
cessor is to use two of the 

FLAG

 pins as asynchronous data receive and 

transmit signals. 

Data Types and Companding

Linear transfers occur in the primary channel, if the channel is active and 
companding is not selected for that channel. Companded transfers occur 
if the channel is active and companding is selected for that channel. The 
multichannel compand select registers, 

MTxCCSy

 and 

MRxCCSy

, specify the 

transmit and receive channels that are companded when multichannel 
mode is enabled. 

Transmit or receive sign extension is selected by bit 0 of 

DTYPE

 in the 

SPCTLx

 register and is common to all transmit or receive channels. If bit 0 

of 

DTYPE

 is set, sign extension occurs on selected channels that do not have 

companding selected. If this bit is not set, the word contains zeros in the 
MSB positions. Companding is not supported for B channel. For B 
channels, transmit or receive sign extension is selected by bit 0 of 

DTYPE

 in 

the 

SPCTLx

 register.

The compression for transmission requires a minimum word 
length of 8 (

SLEN

 = 8) for proper function. If 

SLEN

 < 8 the expan-

sion may not work correctly. 

www.BDTIC.com/ADI

Summary of Contents for SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments