manualshive.com logo in svg

Analog Devices SHARC ADSP-214 Series, Hardware Reference Manual, Page: 361 / 1192

Share
Download
Analog Devices SHARC ADSP-214 Series Hardware Reference Manual Download Page 361

ADSP-214xx SHARC Processor Hardware Reference

6-65 

FFT/FIR/IIR Hardware Modules

Channels Complete Interrupt

 – This interrupt is generated when all the 

channels are complete or when one iteration of time slots completes.

MAC Status Interrupt

 – The status interrupt sources are derived from the 

FIRMACSTAT

 register. 

For more information, see “IIR MAC Status Register 

(IIRMACSTAT)” on page A-91.

Service Channel Interrupts

 – Based on the 

IIR_CCINTR

 bit in the 

IIRCTL1

 

register, both bits (

IIR_DMAWCDONE

 or 

IIR_DMAACDONE

) are set in the 

IIRDMSTAT

 register if either of the conditions is met. The interrupt service 

routine should read (to clear) both bits.

Service MAC Status Interrupts

 – A MAC status interrupt is generated 

whenever a floating-point operation results in an arithmetic exception. 
Reading the 

IIRMACSTAT

 register returns for which MAC unit is causing an 

exception. 

Debug Features

The following sections describe the debugging features available on the 
accelerator.

Local Memory Access

The contents of IIR delay line and coefficient memories are made observ-
able for debug by setting the 

IIR_DBGMODE

/

IIR_DBGMEM

 and 

IIR_HLD

 bits in 

the 

IIRDEBUGCTL

 control register. The debug address register (

IIRDBGADDR

) 

and four data registers are provided for debug operations. Bit 11 of the 
this register selects coefficient memory if set (=1) and selects delay line 
memory in cleared (=0).

The 40-bit wide debug mode read data register is organized as:

• The 

IIRDBGRDDATA_L

 register holds the lower 32 bits

• The 

IIRDBGRDDATA_H

 register holds the upper 8 bits

www.BDTIC.com/ADI

Summary of Contents for SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments