manualshive.com logo in svg

Analog Devices SHARC ADSP-214 Series, Hardware Reference Manual, Page: 284 / 1192

Share
Download
Analog Devices SHARC ADSP-214 Series Hardware Reference Manual Download Page 284

Interrupts

4-20

ADSP-214xx SHARC Processor Hardware Reference

If the DMA is disabled but the associated link buffer is enabled, then a 
maskable interrupt is generated whenever a receive buffer is not empty or 
when a transmit buffer is not full. This interrupt is the same interrupt vec-
tor associated with the completion of the DMA block transfers. 

The interrupt latch bit may be unmasked by the corresponding mask bit 
in the same register. When initially enabling the mask bit, the correspond-
ing latch bit should be cleared first to clear out any request that may have 
been inadvertently latched.

The interrupt service routine should test the buffer status or write to check 
when the buffer is empty or full, in order to determine when it should 
return from interrupt. This reduces the number of interrupts the ISR 
must service.

For core interrupts programs need to perform two writes to the transmit 
buffer to fill it. For the receiver, programs need to perform two reads from 
the receive buffer to empty it. Then the next interrupt occurs when the 
buffer becomes not full or not empty again. Two reads and or writes are 
performed because the link port FIFO depth is two.

Service Request Interrupts

Link port service requests let a disabled (unassigned or assigned with buf-
fer disabled) link port cause an interrupt when an external access is 
attempted. The transmit (

LTRQ

) and receive (

LRRQ

) request status bits of 

the 

LCTLx

 register indicate when another processor is attempting to send 

or receive data through a particular link port. Two processors can commu-
nicate without prior knowledge of the transfer direction, link port 
number, or exactly when the transfer is to occur. The 

LCTLx

 register is 

described in regs appendix.

When 

LxACK

 or 

LxCLK

 is asserted externally, a link service request (LSR) is 

generated in a disabled (unassigned or assigned with buffer disabled) link 
port. Each LSR is gated by mask bits before being latched in the 

LSTATx

 

register. The two possible receive LSRs and the two possible transmit 

www.BDTIC.com/ADI

Summary of Contents for SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments