manualshive.com logo in svg

Analog Devices Blackfin ADSP-BF537, Hardware Reference Manual

The Analog Devices Blackfin ADSP-BF537 is a cutting-edge processor renowned for its exceptional performance and versatility. Unlock the full potential of this remarkable hardware by downloading the comprehensive and free Hardware Reference Manual from our website. All the information you need is just a click away.

Share
Download
background image

Interface Overview

12-4

ADSP-BF537 Blackfin Processor Hardware Reference

 

of signals for receive. The receive and transmit functions are programmed 
separately. Each SPORT is a full duplex device, capable of simultaneous 
data transfer in both directions. The SPORTs can be programmed for bit 
rate, frame sync, and number of bits per word by writing to mem-
ory-mapped registers.

L

In this text, the naming conventions for registers and signals use a 
lower case 

x

 to represent a digit. In this chapter, for example, the 

name 

RFSx

 signals indicates 

RFS0

 and 

RFS1

 (corresponding to 

SPORT0 and SPORT1, respectively). In this chapter, LSB refers to 
least significant bit, and MSB refers to most significant bit.

Port J contains the SPORT0 pins. Some of the SPORT0 pins are multi-
plexed and can be used for other purposes if the entire SPORT0 block or 
some of its signals are not required by an application. However, all pins 
default to the SPORT0 module settings after reset.

The secondary data pins of SPORT0 are multiplexed with the CAN inter-
face. Unless the 

PJCE

 bit in the 

PORT_MUX

 register is set, the CAN signals 

are disabled and the secondary data signals control the associated pins, by 
default. Similarly, the 

PJSE

 bit can disconnect some of the transmit signals 

and redirect the respective pins to the SPI module. The remaining 
SPORT0 signals aren’t multiplexed. Nevertheless, they can be sensed by 
the timer module as alternative clock modules, regardless of whether 
SPORT0 is enabled or not. See 

Figure 14-4 on page 14-8

 for details.

SPORT1 resides in port G. Its signals are mainly shared with upper PPI 
data lines. By default, all port G pins are configured in GPIO mode. Writ-
ing a 1 to bits 8–15 of the 

PORTG_FER

 register enables either PPI or 

SPORT1 signals on the respective pins. If the 

PGSE

, 

PGRE

, and 

PGTE

 bits in 

the 

PORT_MUX

 register are also set, the full SPORT1 functionality is 

enabled, while the PPI can still operate in 8-bit mode. See 

Figure 14-2 on 

page 14-6

 for details.

Summary of Contents for Blackfin ADSP-BF537



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Blackfin ADSP-BF537

D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Manual preview
AirPlus XtremeG Ethernet-to-Wireless Bridge...
Brand: D-Link Pages: 31
Roland VP-9000 Turbostart preview
VP-9000
Brand: Roland Pages: 2
Realtek RTL8187SE User Manual preview
RTL8187SE
Brand: Realtek Pages: 30
Zoom B9.1ut Operation Manual preview
B9.1ut
Brand: Zoom Pages: 88
Omron ACCURAX G5 - Quick Start Manual preview
ACCURAX G5 -
Brand: Omron Pages: 13
NXP Semiconductors UM10301 PCA8565 User Manual preview
UM10301 PCA8565
Brand: NXP Semiconductors Pages: 54
Intel E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor Datasheet preview
E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor
Brand: Intel Pages: 112
Radica Games DAVID-II 716 Operating And Maintenance Instruction Manual preview
DAVID-II 716
Brand: Radica Games Pages: 40
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
Renesas HD74HCT1G04 Datasheet preview
HD74HCT1G04
Brand: Renesas Pages: 8
Variscite VAR-SOM-MX8M-PLUS Quick Start Manual preview
VAR-SOM-MX8M-PLUS
Brand: Variscite Pages: 2
ETAS XETK-S21.0B User Manual preview
XETK-S21.0B
Brand: ETAS Pages: 68
DPS Telecom D-PK-NG432 User Manual preview
D-PK-NG432
Brand: DPS Telecom Pages: 80
Mitsubishi M16C/20 Series Software Manual preview
M16C/20 Series
Brand: Mitsubishi Pages: 188
Transition Networks E-BR-SIC User Manual preview
E-BR-SIC
Brand: Transition Networks Pages: 1
TERSUS Precis-BX305 Quick Start Manual preview
Precis-BX305
Brand: TERSUS Pages: 7
Azoteq IQ Switch ProxSense RS100 Application Notes preview
IQ Switch ProxSense RS100
Brand: Azoteq Pages: 9
Akasa Venom A10 User Manual preview
Venom A10
Brand: Akasa Pages: 2

Brands by name

Popular brands

Load more brands