manualshive.com logo in svg

Analog Devices Blackfin ADSP-BF537, Hardware Reference Manual

The Analog Devices Blackfin ADSP-BF537 is a cutting-edge processor renowned for its exceptional performance and versatility. Unlock the full potential of this remarkable hardware by downloading the comprehensive and free Hardware Reference Manual from our website. All the information you need is just a click away.

Share
Download
background image

ADSP-BF537 Blackfin Processor Hardware Reference

8-41 

 

Ethernet MAC

•

TX frame status interrupt

 – The TX frame status interrupt condi-

tion is signalled whenever the logical AND of the TX sticky frame 
status register and the TX frame status interrupt enable register is 
nonzero. This condition is cleared by writing 1s to all of the TX 
sticky frame status register bits that are enabled in the TX frame 
status interrupt enable register.

•

Wakeup frame detected

 – This bit is set when a wakeup event is 

detected by the MAC core (either a magic packet or a remote 
wakeup packet is accepted by the wakeup filters). This condition is 
cleared by writing a 1 to the 

MPKS

 and/or 

RWKS

 status bits in the 

wakeup control status register.

•

RX DMA direction error detected

 – This bit is set if an RX data or 

status DMA request is granted by the DMA channel, but the DMA 
is programmed to transfer in the wrong (memory-read) direction. 
This could indicate a software problem in managing the RX DMA 
descriptor queue. This interrupt is non-maskable in the MAC and 
must always be handled. This condition is cleared by writing a 1 to 
the 

RXDMAERR

 bit in the MAC system status register.

•

TX DMA direction error detected

 – This bit is set if a TX data or 

status DMA request is granted by the DMA channel, but the DMA 
is programmed to transfer in the wrong direction. Data DMA 
should be memory-read, status DMA should be memory-write. 
This could indicate a software problem in managing the TX DMA 
descriptor queue. This interrupt is non-maskable in the MAC and 
must always be handled. This condition is cleared by writing a 1 to 
the 

TXDMAERR

 bit in the MAC system status register.

•

Station management transfer done

 – This bit is set when a station 

management transfer (on MDC/MDIO) has completed, provided 
the 

STAIE

 interrupt enable control bit is set in the station manage-

ment address register.

Summary of Contents for Blackfin ADSP-BF537



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Blackfin ADSP-BF537

TC Electronic M300 Service Manual preview
M300
Brand: TC Electronic Pages: 2
Lauterbach C2000 Manual preview
C2000
Brand: Lauterbach Pages: 61
T&D RTR-50 User Manual preview
RTR-50
Brand: T&D Pages: 122
Ubiquiti PowerBeam AC Gen2 Quick Start Manual preview
PowerBeam AC Gen2
Brand: Ubiquiti Pages: 22
National Instruments PCI-6110E/6111E User Manual preview
PCI-6110E/6111E
Brand: National Instruments Pages: 113
Supermicro Optane Persistent Memory 200 Series User Manual preview
Optane Persistent Memory 200 Series
Brand: Supermicro Pages: 54
ZALMAN CNPS5700D-Cu User Manual preview
CNPS5700D-Cu
Brand: ZALMAN Pages: 7
ZiLOG Z8 GP ZGP323 User Manual preview
Z8 GP ZGP323
Brand: ZiLOG Pages: 11
ExtraHop EDA 4200 Install preview
EDA 4200
Brand: ExtraHop Pages: 2
S&P Turbo-3000 Operating Instructions preview
Turbo-3000
Brand: S&P Pages: 3
ProSoft MVI46-PDPS User Manual preview
MVI46-PDPS
Brand: ProSoft Pages: 53
AES BeBoPr++ User Manual preview
BeBoPr++
Brand: AES Pages: 44
Homeworks HQP7-RF-2 Installation Instructions Manual preview
HQP7-RF-2
Brand: Homeworks Pages: 24
LevelOne FSW-0512 Specification Sheet preview
FSW-0512
Brand: LevelOne Pages: 2
Me VS-M1 Instructions Manual preview
VS-M1
Brand: Me Pages: 28
Paradyne JetFusion 2004 User Manual preview
JetFusion 2004
Brand: Paradyne Pages: 216
G&D ControlCenter-IP 2.0 Installation Manual preview
ControlCenter-IP 2.0
Brand: G&D Pages: 60
Alphacool GPX-N 1080Ti-M23 Instruction Manual preview
GPX-N 1080Ti-M23
Brand: Alphacool Pages: 4

Brands by name

Popular brands

Load more brands