manualshive.com logo in svg

Analog Devices Blackfin ADSP-BF537, Hardware Reference Manual

The Analog Devices Blackfin ADSP-BF537 is a cutting-edge processor renowned for its exceptional performance and versatility. Unlock the full potential of this remarkable hardware by downloading the comprehensive and free Hardware Reference Manual from our website. All the information you need is just a click away.

Share
Download
background image

ADSP-BF537 Blackfin Processor Hardware Reference

6-15 

 

External Bus Interface Unit

Asynchronous write bus cycles proceed as follows.

1. At the start of the setup period, 

AMS[x]

, the address bus, data buses, 

and 

ABE[1:0]

 become valid. See 

“Byte Enables” on page 6-18

 for 

more information.

2. At the beginning of the write access period, 

AWE

 asserts.

3. At the beginning of the hold period, 

AWE

 deasserts.

Figure 6-4. Asynchronous Write and Read Bus Cycles

SETUP

2 CYCLES

WRITE ACCESS

2 CYCLES

HOLD

1 CYCLE

SETUP

2 CYCLES

READ ACCESS

3 CYCLES

HOLD

CLKOUT

ADDR[19:1]

DATA[15:0]

TRANSITION
TIME

D2

BE1

A1

A2

D1

DATA LATCHED

1 CYCLE 1 CYCLE

AOE

ARE

AWE

[X]

AMS

[

1:0]

ABE

Summary of Contents for Blackfin ADSP-BF537



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Blackfin ADSP-BF537

Acconeer A111 User Manual preview
A111
Brand: Acconeer Pages: 32
Dave Embedded Systems ARM Cortex-A9 MPCore Quick Start Manual preview
ARM Cortex-A9 MPCore
Brand: Dave Embedded Systems Pages: 67
Jabra A330 Multiuse User Manual preview
A330 Multiuse
Brand: Jabra Pages: 15
Keithley 7707 User Manual preview
7707
Brand: Keithley Pages: 59
Octavo OSD3358-SM-RED Getting Started Manual preview
OSD3358-SM-RED
Brand: Octavo Pages: 28
Obihai OBi110 Quick Start Manual preview
OBi110
Brand: Obihai Pages: 2
Commell ES-270 User Manual preview
ES-270
Brand: Commell Pages: 36
Commell CMB-673 Installation Manual preview
CMB-673
Brand: Commell Pages: 9
ESD ECS-CPCIs/FPGA Hardware Manual preview
ECS-CPCIs/FPGA
Brand: ESD Pages: 28
National Instruments PCI-6110E/6111E User Manual preview
PCI-6110E/6111E
Brand: National Instruments Pages: 113
NXP Semiconductors UM10301 PCA8565 User Manual preview
UM10301 PCA8565
Brand: NXP Semiconductors Pages: 54
QTech QSW-2900 User Manual preview
QSW-2900
Brand: QTech Pages: 406
Acces I/O products mPCIe-ADI12-8 Hardware Manual preview
mPCIe-ADI12-8
Brand: Acces I/O products Pages: 13
Planet IEEE 802.3at User Manual preview
IEEE 802.3at
Brand: Planet Pages: 2
Actisense W2K-1 Install And User Manual preview
W2K-1
Brand: Actisense Pages: 14
NetApp AFF A400 Manual preview
AFF A400
Brand: NetApp Pages: 121
SunFounder R3 Manual preview
R3
Brand: SunFounder Pages: 527
eTung LED-328 User Manual preview
LED-328
Brand: eTung Pages: 31

Brands by name

Popular brands

Load more brands