Analog Devices ADuCM310 Hardware Reference Manual Download Page 115

Page: 115 / 192

ADuCM310 Hardware Reference Manual

UG-549

Rev. C | Page 115 of 192

REGISTER DETAILS: I

Master Control Register

Address: 0x40003000, Reset: 0x0000, Name: I2CMCON

Table 153. Bit Descriptions for I2CMCON

Bits

Bit Name

Description

Reset

Access

[15:12]

RESERVED

Reserved.

0x0

MTXDMA

Enable master Tx DMA request.

0x0

0: disable DMA mode.

1: enable I

C master DMA Tx requests.

MRXDMA

Enable master Rx DMA request.

0x0

0: disable DMA mode.

1: enable I

C master DMA Rx requests.

RESERVED

Reserved.

0x0

IENCMP

Transaction completed (or stop detected) interrupt enable.

0x0

0: an interrupt is not generated when a stop is detected.

1: an interrupt is generated when a stop is detected.

IENACK

Acknowledge not received interrupt enable.

0x0

0: disable acknowledge not received interrupt.

1: enable acknowledge not received interrupt.

IENALOST

Arbitration lost interrupt enable.

0x0

0: disable arbitration lost interrupt.

1: enable arbitration lost interrupt.

IENMTX

Transmit request interrupt enable.

0x0

0: disable transmit request interrupt.

1: enable transmit request interrupt.

IENMRX

Receive request interrupt enable.

0x0

0: disable receive request interrupt.

1: enable receive request interrupt.

STRETCH

Stretch SCL enable.

0x0

0: disable clock stretching.

1: setting this bit tells the device if SCL is 0, hold it at 0; or if SCL is 1, hold SCL
at 0 when it next goes to 0.

LOOPBACK

Internal loopback enable. Note that is also possible for the master to loop
back a transfer to the slave as long as the device address corresponds, that is,
external loopback.

0x0

0: SCL and SDA out of the device are not muxed onto their corresponding inputs.

1: SCL and SDA out of the device are muxed onto their corresponding inputs.

COMPETE

Start backoff disable. Setting this bit enables the device to compete for
ownership even if another device is currently driving a start condition.

0x0

MASEN

Master enable. Disable the master when not in use, which gates the clock to

the master and saves power. Do not clear this bit until a transaction has
completed; see the TCOMP bit in the master status register.

0x0

0: master is disabled.

1: master is enabled.

Summary of Contents for ADuCM310

































































































































































































Search results

Summary of Contents for ADuCM310

Reviews:

Related manuals for ADuCM310

Brands by name

Popular brands

Analog Devices ADuCM310, Hardware Reference Manual

Search results

Summary of Contents for ADuCM310

Reviews:

Related manuals for ADuCM310

Brands by name

Popular brands