manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual

The Analog Devices ADSP-21261 SHARC is a powerful digital signal processor designed specifically for audio applications. Enhance your understanding of this innovative product by accessing its comprehensive Hardware Reference Manual. This invaluable manual can be downloaded for free from manualshive.com, providing you with essential insights and technical guidance.

Share
Download
background image

Enabling a Timer

14-8

ADSP-2126x SHARC Processor Hardware Reference

 

• Width is equal to zero

• Period value is lower than width value

• Width is equal to period

On invalid conditions, the timer sets both the 

TMxOVF

 and the 

TIMIRQx

 bits 

and the Count register is not altered. Note that after reset, the timer regis-
ters are all zero.

As mentioned earlier, 2 x 

TMxPRD

 is the period of the PWM waveform and 

2 x 

TMxW

 is the width. If the period and width values are valid after the 

timer is enabled, the Count register is loaded with the value resulting from 

Figure 14-3. Timer Flow Diagram - PWM_OUT Mode

DATA BUS

RESET

TIMER_ENABLE

TMxPRD

TMxW

CLOCK

YES

INTERRUPT

HIGH

LOW

TMRX

EQUAL?

TMxCNT

YES

PWMOUT

LOGIC

EQUAL?

SET PWMOUT

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

Paradyne 4300 Installation Instructions Manual preview
4300
Brand: Paradyne Pages: 22
Xinje XG Series User Manual preview
XG Series
Brand: Xinje Pages: 76
Salus PL07 Instruction Manual preview
PL07
Brand: Salus Pages: 16
AMD SB710 User Manual preview
SB710
Brand: AMD Pages: 20
Patton electronics Model 2711 User Manual preview
Model 2711
Brand: Patton electronics Pages: 13
Teletronics International TT 900 User Manual preview
TT 900
Brand: Teletronics International Pages: 57
AOpen VA1000 Lite2 User Manual And Technical Manual preview
VA1000 Lite2
Brand: AOpen Pages: 18
Thermaltake Extreme Spirit Il Instruction preview
Extreme Spirit Il
Brand: Thermaltake Pages: 2
swiftech MCW5000-64RH Installation Manual preview
MCW5000-64RH
Brand: swiftech Pages: 2
DFRobot FIT0677 Assembly Manual preview
FIT0677
Brand: DFRobot Pages: 30
Taiwan Commate Computer Inc. P2BXA-V Quick Installation preview
P2BXA-V
Brand: Taiwan Commate Computer Inc. Pages: 25
Greenlee 910FS Instruction Manual preview
910FS
Brand: Greenlee Pages: 52
uneron eSOM3735z Quick Start Manual preview
eSOM3735z
Brand: uneron Pages: 13
Microscan MS-96 Vial Reader User Manual preview
MS-96 Vial Reader
Brand: Microscan Pages: 67
Roland JV80 Owner'S Manual preview
JV80
Brand: Roland Pages: 224
IceManCooler ICE-SKY-E User Manual preview
ICE-SKY-E
Brand: IceManCooler Pages: 2
Eneo PNR-5332/3TB Quick Installation Manual preview
PNR-5332/3TB
Brand: Eneo Pages: 49
Jabra A330 Multiuse Technical Specifications preview
A330 Multiuse
Brand: Jabra Pages: 2

Brands by name

Popular brands

Load more brands