manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual

The Analog Devices ADSP-21261 SHARC is a powerful digital signal processor designed specifically for audio applications. Enhance your understanding of this innovative product by accessing its comprehensive Hardware Reference Manual. This invaluable manual can be downloaded for free from manualshive.com, providing you with essential insights and technical guidance.

Share
Download
background image

DAI Interrupt Controller

12-30

ADSP-2126x SHARC Processor Hardware Reference

 

cleared. When the 

DAI_IRPTL_L

 register is read, the low priority latched 

interrupts are all cleared.

Rising and Falling Edge Masks

For interrupt sources that correspond to waveforms (as opposed to DAI 
event signals such as DMA complete or buffer full), the edge of a wave-
form may be used as an interrupt source as well. Just as interrupts can be 
generated by a source, interrupts can also be generated latched on the ris-
ing (or falling) edges of a signal. This concept does not exist in the main 
Interrupt Controller, only in the DAI Interrupt Controller.

When a signal comes in, the system needs to determine what kind of sig-
nal it is and what kind of protocol, as a result, to service. The preamble 
indicates the signal type. When the protocol changes, output (signal) type 
is noted.

For audio applications, the ADSP-2126x needs information about inter-
rupt sources that correspond to waveforms (not event signals). As a result, 
the falling edge of the waveform may be used as an interrupt source as 
well. Programs may elect to use any of four conditions:

• Latch on the rising edge

• Latch on the falling edge

• Latch on 

both

 the rising and falling edge

The DAI Interrupt Controller may be configured using three registers. 
Each of the 32 interrupt lines can be independently configured to trigger 
in response to the incoming signal’s rising edge, its falling edge, both the 
rising edge and the falling edge, or neither the rising edge nor the falling 
edge. Setting a bit in either the 

DAI_IRPTL_RE

 or 

DAI_IRPTL_FE

 registers 

enables the interrupt level on the rising and falling edges, respectively. For 
more information on these registers, see 

Figure A-76 on page A-172

 and 

Figure A-76 on page A-172

.

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

Paradyne 3172 Quick Reference preview
3172
Brand: Paradyne Pages: 20
Paradyne Compshere 3000 Series Notice preview
Compshere 3000 Series
Brand: Paradyne Pages: 2
Lanner electronics EM-566 Series Manual preview
EM-566 Series
Brand: Lanner electronics Pages: 59
Z3 Technology Z3-SBE264-10 User Instructions preview
Z3-SBE264-10
Brand: Z3 Technology Pages: 67
Boss Vocal Performer VE-20 Owner'S Manual preview
Vocal Performer VE-20
Brand: Boss Pages: 20
Concept Pro DEEP LEARNING PLUS Quick Start Manual preview
DEEP LEARNING PLUS
Brand: Concept Pro Pages: 28
Cooler Master Masterliquid ML240L RGB Manual preview
Masterliquid ML240L RGB
Brand: Cooler Master Pages: 18
ST STA309A Operation Manual preview
STA309A
Brand: ST Pages: 67
Vantec Aeroflow FX 120 VAF-1225 User Manual preview
Aeroflow FX 120 VAF-1225
Brand: Vantec Pages: 2
Digi NS7520B Series Hardware Reference Manual preview
NS7520B Series
Brand: Digi Pages: 339
NEC EP-753304DU-R User Manual preview
EP-753304DU-R
Brand: NEC Pages: 26
netsys NH-310S User Manual preview
NH-310S
Brand: netsys Pages: 38
Datel DataMAX User Manual preview
DataMAX
Brand: Datel Pages: 8
C-Data FD612H User Manual preview
FD612H
Brand: C-Data Pages: 19
FDI UEZGUI-4357-70WVN User Manual preview
UEZGUI-4357-70WVN
Brand: FDI Pages: 30
Jameco JE1049 User Manual preview
JE1049
Brand: Jameco Pages: 13
NetApp StorageGRID Webscale SG5700 Series Install preview
StorageGRID Webscale SG5700 Series
Brand: NetApp Pages: 15
iSMA CONTROLLI SfAR-S-16DO User Manual preview
SfAR-S-16DO
Brand: iSMA CONTROLLI Pages: 20

Brands by name

Popular brands

Load more brands