manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual, Page: 551 / 846

Share
Download
Analog Devices ADSP-21261 SHARC Hardware Reference Manual Download Page 551

ADSP-2126x SHARC Processor Hardware Reference

12-29 

 

Digital Audio Interface

High and Low Priority Latches 

In the ADSP-2126x, a pair of registers (

DAI_IRPTL_H

 and 

DAI_IRPTL_L

) 

replace functions normally performed by the 

IRPTL

 register. A single regis-

ter (

DAI_IRPTL_PRI

) specifies the latch to which each of these interrupts 

are mapped.

Two registers (

DAI_IRPTL_RE

 and 

DAI_IRPTL_FE

) replace the DAI periph-

eral’s version of the 

IMASK

 register. As with the 

IMASK

 register, these DAI 

registers provide a way to specify which interrupts to notice and handle, 
and which interrupts to ignore. These dual registers function like 

IMASK

 

does, but with a higher degree of granularity.

Signals from the SRU can be used to generate interrupts. For example, 
when 

SRU_EXTMISCA2_INT

 (bit 30) or 

DAI_IRPTL_H

 is set to one, any signal 

from the external miscellaneous Channel 2 generates an interrupt. If set to 
one, DAI interrupts trigger an interrupt in the core and the interrupt latch 
is set. A read of this bit does not reset it to zero. The bit is only set to zero 
when the cause of the interrupt is cleared. A DAI interrupt indicates the 
source (in this case, external miscellaneous A, Channel 2), and checks the 
IVT for an instruction (next operation) to perform.

The 32 interrupt signals within the Interrupt Controller are mapped to 
two interrupt signals in the primary Interrupt Controller of the SHARC 
core. The 

DAI_IRPT_PRI

 register specifies if the Interrupt Controller inter-

rupt is mapped to the high or low core interrupt (1 = high priority and 0 = 
low priority).

The 

DAI_IRPTL_H

 register is a read-only register with bits set for every DAI 

interrupt latched for the high priority core interrupt. The 

DAI_IRPTL_L

 

register is a read-only register with bits set for every DAI interrupt latched 
for the low priority core interrupt. When a DAI interrupt occurs, the low 
or high priority core ISR should interrogate its corresponding register to 
determine which of the 32 interrupt sources to service. When the 

DAI_IRPTL_H

 register is read, the high priority latched interrupts are all 

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments