manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual, Page: 510 / 846

Share
Download
Analog Devices ADSP-21261 SHARC Hardware Reference Manual Download Page 510

FIFO to Memory Data Transfer

11-20

ADSP-2126x SHARC Processor Hardware Reference

 

5. Connect all of the inputs to the IDP by writing to the 

SRU_DAT3

, 

SRU_DAT4

, 

SRU_FS1

, 

SRU_FS2

, 

SRU_CLK1

, and 

SRU_CLK2

 registers. 

Keep the clock and frame sync of the ports connected to 

LOW

 when 

data transfer is not intended.

6. Enable DMA, IDP, and PDAP (if required) by setting each of the 

following bits to one:

• The 

IDP_DMA_EN

 bit (bit 5 of the 

IDP_CTL

 register)

• The 

IDP_PDAP_EN

 bit (bit 31 in 

IDP_PDAP_CTL

 register)

• The 

IDP_ENABLE

 bit (bit 7 in the 

IDP_CTL

 register)

A DAI interrupt is generated at the end of each DMA.

DMA Transfer Notes

The following items provide general information about DMA transfers.

• A DMA can be interrupted by changing the 

IDP_DMA_EN

 bit in the 

IDP_CTL

 register. None of the other control settings (except for the 

IDP_ENABLE

 bit) should be changed. Clearing the 

IDP_DMA_EN

 bit 

(= 0) does not affect the data in the FIFO, it only stops DMA 
transfers. If the IDP remains enabled, an interrupted DMA can be 
resumed by setting the 

IDP_DMA_EN

 bit again.

• Using DMA transfer overrides the mechanism used for inter-

rupt-driven manual reads from the FIFO. When the 

IDP_DMA_EN

 

bit is set, the eighth interrupt in the 

DAI_IRPTL_L

 or 

DAI_IRPTL_H

 

registers (

IDP_FIFO_GTN_INT

) is 

not

 generated. This interrupt 

detects the condition that the number of data available in FIFO is 
more than the number set in the 

IDP_NSET

 bits (bits [3:0]) of the 

IDP_CTL

 register).

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments