manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual

The Analog Devices ADSP-21261 SHARC is a powerful digital signal processor designed specifically for audio applications. Enhance your understanding of this innovative product by accessing its comprehensive Hardware Reference Manual. This invaluable manual can be downloaded for free from manualshive.com, providing you with essential insights and technical guidance.

Share
Download
background image

ADSP-2126x SHARC Processor Hardware Reference

10-53 

 

Serial Peripheral Interface Port

With enabled SPI:

1. Clear the 

RXSPIx

/

TXSPIx

 registers and the buffer status without dis-

abling the SPI by ORing 0xC0000 with the present value in the 

SPICTLx

 registers. Use the 

RXFLSH

 (bit 19) and 

TXFLSH

 (bit 18) bits 

in the 

SPICTLx

 registers to clear the 

RXSPIx/TXSPIx

 registers and 

the buffer status.

2. Disable DMA and clear the FIFO by writing 0x80 to the 

SPIDMACx

 

registers. This ensures that any data from a previous DMA opera-
tion is cleared because 

SPICLK

 runs for five more word transfers 

even after the DMA count is zero in receive DMA.

3. Clear all errors by writing to the W1C-type bits in the 

SPISTATx

 

registers. This ensures that no interrupts occur due to errors from a 
previous DMA operation.

4. Reconfigure the 

SPICTLx

 registers to remove the clear condition on 

the 

TXSPIx

/

RXSPIx

 registers.

5. Configure DMA by writing to the DMA parameter registers 

(described in 

“Setting Up DMA Channel Allocation and Priorities” 

on page 7-17

) and the 

SPIDMACx

 registers using the 

SPIDEN

 bit (bit 

0).

DMA Error Interrupts

The 

SPIUNF

 and 

SPIOVF

 bits of the 

SPIDMACx

 registers indicate transmission 

errors during a DMA operation in slave mode. When one of the bits is set, 
an SPI interrupt occurs. The following sequence details the steps to 
respond to this interrupt.     

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

YASKAWA A1000 Series Installation Manual preview
A1000 Series
Brand: YASKAWA Pages: 34
3Com 3CRSHPW196 User Manual preview
3CRSHPW196
Brand: 3Com Pages: 16
Commell ES-270 User Manual preview
ES-270
Brand: Commell Pages: 36
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Brand: LGC wireless Pages: 154
ZKTeco HVR0402 User Manual preview
HVR0402
Brand: ZKTeco Pages: 68
IBM 2078-4F4 Quick Installation Manual preview
2078-4F4
Brand: IBM Pages: 130
V-Count Ultima Go Quick Installation Manual preview
Ultima Go
Brand: V-Count Pages: 2
Digi DataFire GO! PRO Manual preview
DataFire GO! PRO
Brand: Digi Pages: 20
Kontron AdvancedTCA AT8901M User Manual preview
AdvancedTCA AT8901M
Brand: Kontron Pages: 76
Buffalo LinkStation 500 User Manual preview
LinkStation 500
Brand: Buffalo Pages: 139
B&B Electronics PCMCIA 232PCC2 Owner'S Manual preview
PCMCIA 232PCC2
Brand: B&B Electronics Pages: 24
SilverStone argon series User Manual preview
argon series
Brand: SilverStone Pages: 16
ICP DAS USA VEX-112 Quick Start Manual preview
VEX-112
Brand: ICP DAS USA Pages: 8
Yeastar Technology YE110 Instruction preview
YE110
Brand: Yeastar Technology Pages: 2
RadiSys ES4001G ONT Quick Installation Manual preview
ES4001G ONT
Brand: RadiSys Pages: 6
Linksys EFG20 User Manual preview
EFG20
Brand: Linksys Pages: 37
Garland EdgeSafe M40G1AC User Manual preview
EdgeSafe M40G1AC
Brand: Garland Pages: 159
RTI RP-4 Quick Reference Manual preview
RP-4
Brand: RTI Pages: 4

Brands by name

Popular brands

Load more brands