manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual

The Analog Devices ADSP-21261 SHARC is a powerful digital signal processor designed specifically for audio applications. Enhance your understanding of this innovative product by accessing its comprehensive Hardware Reference Manual. This invaluable manual can be downloaded for free from manualshive.com, providing you with essential insights and technical guidance.

Share
Download
background image

ADSP-2126x SHARC Processor Hardware Reference

9-1 

 

9 SERIAL PORTS

The ADSP-2126x processors have up to six independent, synchronous 
serial ports (SPORTs) that provide an I/O interface to a wide variety of 
peripheral devices. Each serial port has its own set of control registers and 
data buffers. With a range of clock and frame synchronization options, the 
SPORTs allow a variety of serial communication protocols and provide a 
glueless hardware interface to many industry-standard data converters and 
codecs.

The number of serial ports varies depending on the specific proces-
sor model you are using. This chapter was written using six serial 
ports for examples. Programs need to be written accordingly.

Serial ports can operate at one-quarter the full clock rate of the processor, 
at a maximum clock rate of n/4M bit/s, where n equals the processor 
core-clock frequency (

CCLK

). If channels A and B are active, each SPORT 

has 100M bit/s maximum throughput. Bidirectional (transmit or receive) 
functions provide greater flexibility for serial communications. Serial port 
data can be automatically transferred to and from on-chip memory using 
DMA block transfers. In addition to standard synchronous serial mode, 
each serial port offers a Time Division Multiplexed (TDM) multichannel 
mode, Left-justified Sample Pair mode, and I

2

S mode.

Serial ports offer the following features and capabilities:

• Two bidirectional channels (A and B) per serial port, configurable 

as either transmitters or receivers. Each serial port can also be con-
figured as two receivers or two transmitters, permitting two 
unidirectional streams into or out of the same serial port. This 

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Brand: Baracoda Pages: 42
EAW MX250 Owner'S Manual preview
MX250
Brand: EAW Pages: 10
Xinje XG Series User Manual preview
XG Series
Brand: Xinje Pages: 76
National Instruments NI 9213 Getting Started preview
NI 9213
Brand: National Instruments Pages: 11
Aleratec 310108 Quick Start Manual preview
310108
Brand: Aleratec Pages: 12
Supero AOC-SIMLC User Manual preview
AOC-SIMLC
Brand: Supero Pages: 68
PairGain PG-FLEX RT FRL-752 Manual preview
PG-FLEX RT FRL-752
Brand: PairGain Pages: 6
A4Tech RH-10 User Manual preview
RH-10
Brand: A4Tech Pages: 8
National Instruments NI 447 Series User Manual preview
NI 447 Series
Brand: National Instruments Pages: 80
Advantech SOM-C350 User Manual preview
SOM-C350
Brand: Advantech Pages: 108
Accusys ACS-7630 User Manual preview
ACS-7630
Brand: Accusys Pages: 34
Datum bc635VME Operation And Technical Manual preview
bc635VME
Brand: Datum Pages: 49
ICS ELECTRONICS VXI-5501 Quick Start Manual preview
VXI-5501
Brand: ICS ELECTRONICS Pages: 4
Smacq Technologies PCI-1232 User Manual preview
PCI-1232
Brand: Smacq Technologies Pages: 22
Barracuda CloudGen Firewall Revision preview
CloudGen Firewall
Brand: Barracuda Pages: 8
Lantronix N-FXE 02B Series User Manual preview
N-FXE 02B Series
Brand: Lantronix Pages: 10
HighPoint SSD7202 Quick Installation Manual preview
SSD7202
Brand: HighPoint Pages: 12
ACTi GNR-410 Quick Installation Manual preview
GNR-410
Brand: ACTi Pages: 12

Brands by name

Popular brands

Load more brands