manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual

The Analog Devices ADSP-21261 SHARC is a powerful digital signal processor designed specifically for audio applications. Enhance your understanding of this innovative product by accessing its comprehensive Hardware Reference Manual. This invaluable manual can be downloaded for free from manualshive.com, providing you with essential insights and technical guidance.

Share
Download
background image

Boundary Scan

6-2

ADSP-2126x SHARC Processor Hardware Reference

 

A Boundary Scan Description language (BSDL) file for the ADSP-2126x 
is available on the Analog Devices Web site.

Refer to the IEEE 1149.1 JTAG specification for detailed information on 
the JTAG interface. This chapter assumes a working knowledge of the 
JTAG specification.

Boundary Scan

A boundary scan allows a system designer to test interconnections on a 
printed circuit board with minimal test-specific hardware. The scan is 
made possible by the ability to control and monitor each input and output 
pin on each chip through a set of serially scannable latches. Each input 
and output is connected to a latch, and the latches are connected as a long 
Shift register so that data can be read from or written to them through a 
serial test access port (TAP). The ADSP-2126x contains a test access port 
compatible with the industry-standard IEEE 1149.1 (JTAG) specification. 
Only the IEEE 1149.1 features specific to the ADSP-2126x are described 
here. For more information, see the IEEE 1149.1 specification and the 
other documents listed in 

“References” on page 6-9

.

The boundary scan allows a variety of functions to be performed on each 
input and output signal of the ADSP-2126x. Each input has a latch that 
monitors the value of the incoming signal and can also drive data into the 
chip in place of the incoming value. Similarly, each output has a latch that 
monitors the outgoing signal and can also drive the output in place of the 
outgoing value. For bidirectional pins, the combination of input and out-
put functions is available.

Every latch associated with a pin is part of a single serial shift register path. 
Each latch is a master/slave type latch with the controlling clock provided 
externally. This clock (

TCK

) is asynchronous to the ADSP-2126x system 

clock (

CLKIN

).

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

H3C H3C S7500E Series Instruction Manual preview
H3C S7500E Series
Brand: H3C Pages: 34
H3C SR8800 IM-FW-II Manual preview
SR8800 IM-FW-II
Brand: H3C Pages: 5
H3C H3C S7500E Series Installation Manual preview
H3C S7500E Series
Brand: H3C Pages: 50
Patton electronics 1084 Installation And Operation Manual preview
1084
Brand: Patton electronics Pages: 16
Yamaha DX7mega128 Install Manual preview
DX7mega128
Brand: Yamaha Pages: 6
Yamaha DX7 MiniMAX User Manual preview
DX7 MiniMAX
Brand: Yamaha Pages: 4
Yamaha DME Designer Setup Manual preview
DME Designer
Brand: Yamaha Pages: 22
Yamaha PLG100-VL Eigentümer-Handbuch preview
PLG100-VL
Brand: Yamaha Pages: 49
Idis DR-6100 Series Operation Manual preview
DR-6100 Series
Brand: Idis Pages: 86
Paradyne COMSPHERE 3610 Installation Instructions preview
COMSPHERE 3610
Brand: Paradyne Pages: 2
ebm-papst 4112 N/2HU Operating Manual preview
4112 N/2HU
Brand: ebm-papst Pages: 6
ebm-papst 4314 N/2HHPU Operating Manual preview
4314 N/2HHPU
Brand: ebm-papst Pages: 6
ebm-papst 8312 L Operating Manual preview
8312 L
Brand: ebm-papst Pages: 5
Quantum LightSpeed Appliance QLS250 Owner'S Manual preview
LightSpeed Appliance QLS250
Brand: Quantum Pages: 12
Dust Networks SmartMesh IA-510 D2511 Manager'S Manual preview
SmartMesh IA-510 D2511
Brand: Dust Networks Pages: 30
TVT Digital TD-3316B4-16P-A1 Quick Start Manual preview
TD-3316B4-16P-A1
Brand: TVT Digital Pages: 2
Qlogic Storage Networking (Unified Fabric Pilot) Installation Manual preview
Storage Networking (Unified Fabric Pilot)
Brand: Qlogic Pages: 76
Rajant Corporation BreadCrumb CX1 User Manual preview
BreadCrumb CX1
Brand: Rajant Corporation Pages: 40

Brands by name

Popular brands

Load more brands