manualshive.com logo in svg

AMX TDS, Operation/Reference Manual

Share
Download
AMX TDS Operation/Reference Manual Download Page 29

AMX TDS - Terrestrial/Satellite (Standard Definition)

21

AMX TDS (Television Delivery System) 

Product Specifications

DTV-TX01-DVB-T Transmitter

Dimensions (HWD):

2.18" x 5.41" x 7.60" (5.56cm x13.74cm x 19.30cm)

Weight:

2.75 lbs (1.25 kg)

Power Requirements:

• Power Consumption: 6W

• Voltage rating: nominal 12 to 13.5V DC

• Current draw at 12V: 0.5A

Tuners:

2 internal tuners

RF Input Level:

• 480 ˜ 860 MHz

• -35 ˜ -50 dBm

Front Panel Components

• NETWORK Connector:

Standard RJ45 connector.

• LEDs:

Three LEDs indicate the status of the Transmitter:

• Streaming LED (

green

): Flashes if only one tuner is streaming. Steady on if both 

tuners are streaming.

• Network Connectivity LED (

green

): Lights to indicate that the Transmitter is 

connected and communicating with the network.

• Power status LED (

yellow

): Lights to indicate that the Transmitter is receiving 

power, and is functional.

• Common Interface 

Slots 1 & 2: 

Dual Common Interface Slots enable the Transmitter to select encrypted channels 
in cases where this is supported by the broadcaster.

Note: Before de-scrambling content using the Common Interface Slots, ensure that 
you have the appropriate authority/rights to transmit the de-scrambled content on 
your network.

• RESET button:

Press to reboot the Transmitter.

Rear Panel Components:

• RF INPUTs:

Two TV aerial plug/Belling-Lee connectors accept incoming terrestrial signals.

• RF OUTPUTs:

Two RF aerial plug/Belling-Lee connectors allow you to daisy chain 
DTV-TX01-DVB Transmitters together. 

Note: There is a 3db signal loss on RF output relative to the RF input.

• Factory Reset Button:

The recessed Factory Reset button on the rear panel allows you to perform a full 
factory reset (resets flash and reboots the Transmitter in DHCP mode):

• Press and hold the recessed Factory Reset button while simultaneously pressing 

the Reset button on the front panel.

• Continue to hold the Factory Reset button while the unit is rebooting.

• Release when the Streaming Status LED begins to flash. 

• SERIAL (RS232):

DB9 serial connector for local command line interface (RS232 only).

• PWR:

2-pin mini-phoenix connector provides 12VDC power from the power supply.

Note: A 12VDC Power Supply is required (not included)

Environment:

• Operating Temperature: 32°F - 122°F (0°C to 50°C)

• Operating Humidity: Max. relative humidity - 85% (non-condensing)

Certifications:

• CE

• FCC part 15 Class A

Other AMX Equipment:

• DTV-MA01 TDS Management Appliance (FG1412-01)

• DTV-RX01-SD Receiver (FG1411-01)

• DTV-TX02-DVB-S Transmitter (FG1410-02)

• DTV-RK, Rack Mount Kit for DVB-T/S Transmitters (FG1410-60)

• CC-232 Serial Communication Cable (FG10-752-04)

• 12V Power Supply

Summary of Contents for TDS











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands