Quick Start Guide
NXA-BASE/1
Modero Battery Base and Accessories
For more detailed installation, configuration, programming, file transfer, and
operating instructions, refer to the touch panel’s instruction manual,
available on-line at
www.amx.com
.
ATTENTION!
Verify that the Modero panel is using the latest firmware. Verify that the
battery base is loaded with the latest NXA-BASE/1 firmware. These recent
builds of firmware incorporate the necessary updates for using the Modero
with the NXA-BASE/1.
Overview of the NXA-BASE/1 Kit
The NXA-BASE/1 Kit (FG2255-05K) contains one battery and one battery
base. The NXA-BASE/1 (FIG. 2) is a Modero accessory that allows an
NXT-CV7 touch panel to function off the charge from a single internally
connected NXT-BP battery. The base provides both power and battery
information to the panel via the panel interface connector. The NXT-BP
battery can be charged through either the base (only when connected to
the NXT-CV7 touch panel) or through an optional NXT-CHG Modero Power
Station. When used with the optional battery base, the CV7 panels will
charge the battery during full operation.
Specifications
Checking the NXT-BP Charge
1.
Press the Battery Life Indicator button (FIG. 3) once to illuminate the
Battery Life LEDs and display the percent charge remaining on the
battery (
this indication lasts a few seconds
).
2.
Charge the NXT-BP battery by either inserting it into the battery base
or from within the optional NXT-CHG charger (which can sequentially
charge up to two batteries).
Note
: It is recommended to fully charge this battery before using it to power
an NXT-CV7 panel.
ATTENTION!
If the 25% LED indicator is blinking, recharge your battery immediately.
This blinking indicates there is less than 5% of a charge remaining on the
battery.
Installation of an NXT-BP into the NXA-BASE/1
The base does not directly connect to a power supply. Instead, it receives
the power necessary to charge the battery from the Modero panel (through
the Panel Interface connector).
1.
Install the NXT-BP battery into the base’s battery compartment with
the label-side facing up.
2.
Align the battery connector with its corresponding battery connector
port (located in the battery compartment shown in FIG. 4).
3.
Carefully insert the NXT-BP into the base until the battery securely fits
onto the Battery Connector Port.
FIG. 1
NXA-BASE/1 Kit (consists of one BASE/1 and a single NXT-BP)
FIG. 2
NXA-BASE/1 showing Panel Interface and connector locations
NXA-BASE/1 Kit Specifications
Dimensions (HWD):
NXA-BASE/1
(
FG2255-05K
)
NXT-BP
(
FG2255-10
)
• 0.93" x 5.96" x 6.89" (2.36 cm x 15.14 cm x 17.51 cm)
• 0.69" x 3.50" x 5.81" (1.75 cm x 8.89 cm x 14.76 cm)
Power:
• NXA-BASE/1: 1.4 A @ 12 VDC (max power draw while charging a
single battery)
• NXT-BP: Voltage - 11.1 Volts (nominal)
Weight:
• Base unit: 0.75 lbs (0.34 kg)
• NXT-BP: 1.0 lbs (0.45 kg)
• Base and 1 battery: 1.75 lbs (0.79 kg)
NXA-BASE/1:
Features:
• Charge time for single depleted battery: ~ 5 - 8 hours
• Must be connected to a Modero unit utilizing a PSN4.4 power supply
(or higher)
NXT-BP Features:
• Battery Usage: 4 to 8 hours (time is usage dependant)
• Charge Capacity: 6300mAh
NXA-BASE/1
NXT-BP
Battery Base
Modero Power Pack
Panel Interface
connector (male)
Securing
pegs (2)
Front
Back
Battery
locking
mechanism
Battery
latch
Insert holes for
NXT-CV7 feet
Alignment
pegs (2)
slider
NXA-BASE/1 Kit Specifications (Cont.)
Operating / Storage
Environment:
• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage/Discharge Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
Included Accessories:
• N/A
Optional Accessories:
• NXT-CHG Kit (
FG2250-50K
):
1 charger and 2 NXT-BP batteries
• NXT-BP batteries (
FG2255-10
) (additional)
FIG. 3
NXT-BP Modero Power Pack (showing Battery Life Indicator and button)
FIG. 4
Battery installation procedure
Battery Life Indicator
Battery Life (Charge)
button
Its recommended to
fully charge the
batteries before their
initial use
NXT-BP Battery
Battery
Connector
Battery
Connector
Port
FRONT
