Installation Guide
DTV-MA01
TDS Management
Appliance
Overview
The DTV-MA01 TDS Management Appliance (
FG1412-01
) manages television distribution in
an AMX TDS (Television Distribution System) installation (FIG. 1).
Rear Panel Components
12 VDC Power Connector
Connect the power adapter to the unit, and plug the power adapter into an AC power outlet.
Note
: Use ONLY the power adapter supplied with the DTV-MA01. Otherwise, the unit may be
damaged.
Video Output Connectors
The VGA and HDMI Video Output connectors are located on the rear panel:
•
VGA
: The SVGA connector provides analog RGBHV video output.
•
HDMI
: The HDMI connector provides HDMI video output.
10/100 Network Port
The 10/100 (Ethernet RJ45) port on the front panel provides 10/100 BaseT network
connectivity via Cat5/5e/6 network cable. Refer to the
AMX TDS Installation
Overview
section for more information.
Note
: The DTV-MA01 requires Layer 3 switching. Therefore a Layer 3 Network Switch
(sometimes referred to as a "Multilayer Switch") is required to operate properly.
10/100 Network Port Pinouts and Signals
The following table lists the pinouts, signals, and pairing for the 10/100 Network port.
FIG. 2 diagrams the pinouts and signals for the 10/100 Port RJ45 connector and cable. Note
that while 568B termination is shown in the figure, 568A can also be used, as long as both
ends are terminated the same way.
Consult the Network Administrator for correct cabling from the DTV-MA01 onto the network.
•
For remote connectivity, the Firewall may have to be configured to open port
2008
for
remote connectivity over UDP.
•
Ports
5000
and
5001
are required for the Transmitters as well as any ports used for the
TDS Multicast stream.
•
Ports
5002
and
5003
are fixed as the multicast stream output ports.
Ethernet LEDs
Default IP Address
By default, the DTV-MA01 is set to
DHCP
.
Note
:
The DTV-MA01 must be set to a static IP address, or have the DHCP server set
up to always give it the same IP address.
Automatic re-assignment of the IP address via DHCP may cause communication issues with
the TDS system. If the DTV-MA01 is assigned a new IP address, then all TX and RX units in
the system must be rebooted.
Network Switch Requirements
The DTV-MA01 requires a Layer 3 Gigabit Switch with multicast support, IGMP Querier/
Snooping and PIM.
Audio Output Connector
The green 1/8" stereo connector provides analog audio output.
Note
: The Audio in (blue) and Microphone (red) connectors are not used.
FIG. 1
DTV-MA01 TDS Management Appliance
Product Specifications - DTV-MA01 TDS Management Appliance
Dimensions (HWD):
6.54" x 1.89" x 6.46" (16.6 cm x 4.8 cm x 16.4 cm)
Weight:
2.85 lbs (1.3 kg)
Power
• 100-240VAC, 1.5A, 50/60Hz
• 90W (20V, 4.5A) AC Adapter
Environmental:
• Environment Operating Temperature: 0 ~ 50°C (32 ~ 122°F)
• Storage Temperature: -30 ~ 60ºC (-22 ~ 140ºF)
• Relative Humidity : 90% RH (45°C non-Condensing)
Enclosure:
Enclosure SECC with black matte finish
Operating System:
POSReady 2009
Front Panel Components
Status:
Blue LED indicates power status and hard drive activity
Power Switch:
Turns power on/off.
Note
: This is a "soft switch": flipping the switch while the Player is run-
ning issues a shutdown request.
USB Ports:
2 Type-B USB 2.0 Ports for connecting USB mouse and keyboard.
Note
: The Player is designed to be used without a keyboard and mouse;
they are only required for initial configuration and maintenance.
Rear Panel Components
Power Connector:
• 90W (20V,4.5A) AC Adapter
• Input Voltage AC 100-240V
Note
: Isolate IT Power System Connection.
USB Ports:
4 Type-B USB 2.0 Ports.
Ethernet Port:
RJ-45 Ethernet port provides Gigabit Ethernet communication between
the Player and the LAN.
Audio Out:
Provides stereo audio output.
Note
: The Audio in (blue) and Microphone (red) connectors are not
used.
Serial Port:
Reserved for future use.
HDMI Video Out :
Provides HDMI video output to the display.
VGA Video Out:
Provides RGBHV video output to the display.
e-SATA:
Reserved for future use.
Certifications
CE, FCC, UL, CB
Included Accessories
One power adaptor
Other AMX
Equipment:
• DTV-RX01-SD Receiver (FG1411-01)
• DTV-RX02-HD Receiver (FG1411-02)
• DTV-TX01-DVB-T Transmitter (FG1410-01)
• DTV-TX02-DVB-S Transmitter (FG1410-02)
• DTV-TX03-US Transmitter (FG1410-03)
Power Switch
USB Ports
Power
VGA Out
HDMI Out
Ethernet Port
USB Ports
Audio Out
(front)
(rear)
Status light (surrounds the Power Switch)
10/100 Port Pinouts and Signals
Pin
Signals
Connections
Pairing
Color
1
TX +
1 --------- 1
1 --------- 2
Orange-White
2
TX -
2 --------- 2
Orange
3
RX +
3 --------- 3
3 --------- 6
Green-White
4
no connection
4 --------- 4
Blue
5
no connection
5 --------- 5
Blue-White
6
RX -
6 --------- 6
Green
7
no connection
7 --------- 7
Brown-White
8
no connection
8 --------- 8
Brown
FIG. 2
RJ45 wiring diagram
FIG. 3
Ethernet LEDs
SPD - Speed LED
connection speed is 100 Mbps
and turns Off when speed is
lights (yellow) when the
L/A - Link/Activity LED
lights (green) when the
Ethernet cables are
connected and terminated
10 Mbps.
correctly.
