manualshive.com logo in svg

AMS AFDAU T-1, Installation Manual

Share
Download
AMS AFDAU T-1 Installation Manual Download Page 23

 

 

 

 AFDAU-T1 Aerial Firefighting 

Data Acquisition Unit 

 

Installation Manual 

 

AMS-IM-1-01 Rev. 7 

 

22 September 2021 

17 

 

2.2.11  Modems 

For the AFDAU-T1 to be able to transmit event messages a modem must be connected. Various modems are 
supported as listed below and are connected to the AFDAU-T1 via any available RS232 port. 

 

TracPlus RockAIR 

 

Pinouts 

AFDAU-T1 

J1 

RockAIR 

4-Pin Conn. 

Description 

28* 

3 

RS232 Tx 

10* 

4 

RS232 Rx 

* RS232 Ports 1-4 may be used of the AFDAU-T1. Port 2 is shown above.

 

 

TracPlus v2track 

 

Pinouts 

AFDAU-T1 

J1 

v2track 

15-Pin D-Sub 

Description 

28* 

15 

RS232 Tx 

10* 

8 

RS232 Rx 

* RS232 Ports 1-4 may be used of the AFDAU-T1. Port 2 is shown above.

 

 

Flightcell DZMx 

 

 

Pinouts 

AFDAU-T1 

J1 

DZMx Civilian 

J1 (Primary) 

DZMx Military 

J1

 

Description 

28* 

12 

44 

Aux Data Tx 

10* 

13 

45 

Aux Data Rx 

21* 

25 

37 

Chassis Gnd 

* RS232 Ports 1-4 may be used of the AFDAU-T1. Port 2 is shown above. 

 

CAUTION 

THE AFDAU-T1 IS SUPPORTED ON PLATFORM 3 AND 4 OF THE DZMX ONLY. CONTACT 

FLIGHTCELL FOR MORE INFORMATION.

 

 

 

Summary of Contents for AFDAU T-1






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands