Temposonics
®
R-Series
V
Analog
Operation Manual
I 20 I
4.4
Installation and design
of Temposonics
®
RFV
RFV-B – RFV base unit, example: Connection type D60 (connector outlet)
Magnet
11.7
(0.46)
Sensor electronics housing
58
(2.28)
Null zone
61
(2.4)
Dead zone
see table
7
(0.28)
11.4 (0.45)
Not flexible
107 (4.2)
Stroke length
150…20,000
(6…787)
Ø 8 ±0.23
(Ø 0.31 ±0.01)
Tolerance of total length
Dead zone
Stroke length
Up to 7620 mm (300.00 in.)
Up to 10,000 mm (393.70 in.)
Up to 15,000 mm (590.55 in.)
Up to 20,000 mm (787.00 in.)
+8 mm (0.31 in.)/−5 mm (0.20 in.)
+15 mm (0.59 in.)/−15 mm (0.59 in.)
+15 mm (0.59 in.)/−30 mm (1.18 in.)
+15 mm (0.59 in.)/−45 mm (1.77 in.)
94 mm (3.70 in.)
100 mm (3.94 in.)
120 mm (4.72 in.)
140 mm (5.51 in.)
Note:
Tolerance of total length has no influence on the stroke length.
44
(1.7)
Ø
34.6
(Ø
1.36)
Ø 48
(Ø 1.89)
RFV-M/-S – RFV with threaded fl ange M18×1.5-6g or ¾"-16 UNF-3A, example: Connection type D34 (connector outlet)
Magnet
b
13
(0.51)
Not flexible
97 (3.82)
Sensor electronics housing
58
(2.28)
10
(0.39)
Null zone
51
(2)
Stroke length
150…20,000
(6…787)
Dead zone
see table
25
(0.98)
Threaded flange
»M«
:
M18×1.5-6g
Threaded flange
»S«
:
¾"-16 UNF-3A
Ø 8 ±0.23
(Ø 0.31 ±0.01)
Tolerance of total length
Dead zone
Stroke length
Up to 7620 mm (300.00 in.)
Up to 10,000 mm (393.70 in.)
Up to 15,000 mm (590.55 in.)
Up to 20,000 mm (787.00 in.)
+8 mm (0.31 in.)/−5 mm (0.20 in.)
+15 mm (0.59 in.)/−15 mm (0.59 in.)
+15 mm (0.59 in.)/−30 mm (1.18 in.)
+15 mm (0.59 in.)/−45 mm (1.77 in.)
94 mm (3.70 in.)
100 mm (3.94 in.)
120 mm (4.72 in.)
140 mm (5.51 in.)
Note:
Tolerance of total length has no influence on the stroke length.
a
Threaded flange
»M«
»S«
a b
A/F 46 (1.81) 53
(2.09)
A/F 44.5 (1.75) 51.3 (2.02)
Controlling design dimensions are in millimeters and measurements in ( ) are in inches
Fig. 12: Temposonics
®
RFV with ring magnet, part 1