18
ARR 1575
2
Safety measures and instructions
2�3
Fire prevention
•
The oil change point must be where it cannot interfere in explosion or fire hazard areas.
•
It must be identified by “No smoking” and “No open flame” plates and signs.
•
The handling area must be dimensioned so that it can capture a volume of the flammable liquid equal to the capacity of the big-
gest transport container.
•
It must be equipped with portable fire extinguishers.
•
For handling the oil and diesel fuel, use metal barrels, jerry cans, sheet-metal cans and similar vessels.
•
The transport containers must be properly closed during storage.
•
Vessels must be with only one outlet, stored always with the outlet up and secured against the outflow and drains.
•
Vessels must be marked with non-removable writings showing the contents and flammability classes.
Special tools, jigs – see relevant chapters of the manual
2�4
Claim conditions and disclaimer of liability
1� Warranty rules
•
Regular inspections and correct operation of the equipment
•
Products have been registered at the service portal
•
The equipment is operated by a trained operator
•
Following parts are excluded from warranty: part subject to wear and tear, including, without limitation, rubber washers/wheels,
belts, scrapers, wipers, filters, grease, fluids, conveyor parts, chains, foundation boards, compacting rods, auger elements, bearings,
fuel and consumables.
•
Batteries are provided with a warranty for 12 months / 1,000 hours. After this period, batteries are included in parts subject to wear
and tear and are excluded from the warranty.
•
Hydraulic hoses can be purchased from local dealers and charged as an expense to Ammann.
2� Procedure for raising a claim
•
In case of raising a warranty claim, the owner/user shall immediately submit the manufacturer a completed warranty claim and
images of the fault. The owner/user shall also send a proof of regular maintenance before sending the warranty claim or together
with it at the latest.
•
Ammann recommends that you send a proof of regular maintenance regularly.
•
The document can be sent in various ways (e.g. via the service portal, service application). The document shall contain a machine
serial number and a serial number of the original maintenance kit of Ammann. This information can be provided either typed, or
scanned according to the selected manner of handover.
3� Breach
•
If a dealer breaches obligations stated in points 1) and 2), any warranty claims will be rejected.
Summary of Contents for ARR 1575
