AMK Level 5 Installation, Operation And Troubleshooting Download Page 84 | Manualshive

Page: 84 / 104

AMK Level 5 Installation, Operation And Troubleshooting Download Page 84

©

AMK Solac 11252 DeltaSol_BX.monen.ind

d

|

84

Level 5

Time period - switch-on condition

LLOGI/ODB/tDTO

Time period - switch-on
condition
Adjustment range: 1 ... 100 s
in steps of 1 s
Factory setting: 60 s

The parameter

tDTO

is used for adjusting the time period

during which the switch-on condition

DT O

must be per-

manentely fulfi lled.

Stabilisation

LLOGI/ODB/tSTB

Stabilisation
Adjustment range:
1.0 ... 15.0 min
in steps of 0.5 min
Factory setting: 2 min

The parameter tSTB is used for adjusting the time period
during which the switch-off condition

DT F

will be ignored

after the fi lling time has ended.

LLOGI/ODB/tFLL

Filling time
Adjustment range:
1.0 ... 30.0 min
in steps of 0.5 min
Factory setting: 5.0 min

The fi lling time can be adjusted using the parameter

tFLL

.

During this period, the pump runs at 100 % speed.

Filling time

By means of this function, store loading continues after the
temperature difference between the collector and the store
has fallen below the switch-off difference. Store loading is
stopped if the adjusted

∆

T overrun difference between fl ow

and return sensor is underrun.

LLOGI/OOVRU

Selection: ON / OFF
Factory setting: OFF

LLOGI/DTOVR

Adjustment range: 0.0 ... 20.0 K
Factory setting: 5.0 K

Overrun

Note:

The overrun function is only available, if both
Grundfos sensors (VFS and RPS) are used.

Booster function

LLOGI/ODB/OBST

Booster function
Adjustment range: ON / OFF
Factory setting: OFF

This function is used for switching on a second pump when
fi lling the solar system. When solar loading starts, R3/R4 is
energised in parallel to R1. After the fi lling time (

tFLL

) has

ended, R2 is switched off.

Note:

The booster function is available in systems 1, 3,
8, 9, and 10 only.

«
...
82
83
84
85
86
...
»

Summary of Contents for Level 5









































































































Reviews:

No comments