manualshive.com logo in svg

AMK Level 5, Installation, Operation And Troubleshooting, Page: 102 / 104

Share
Download
AMK Level 5 Installation, Operation And Troubleshooting Download Page 102

© 

AMK Solac 11252 DeltaSol_BX.monen.ind

d

|

 102

Level 5

Smart Display SD3 / Large display module GA3

The Smart Display is designed for simple connection to 
controllers with VBus

®

. It is used for visualising data issued 

by the controller: collector temperature, store temperature 
and energy yield of the solar thermal system. The use of 
high-efficiency LEDs and filter glass assures a high optical 
brilliance and good readability even in poor visibility condi-
tions and from a larger distance. An additional power supply 
is not required. One module is required per controller.
The GA3 is a completely mounted large display module for 
visualisation of collector- and store temperatures as well as 
the heat quantity yield of the solar system via one 6-digit 
and two 4-digit 7-segment-displays. An easy connection 
to all controllers with VBus

®

 is possible. The front plate is 

made of antireflective filterglass and is printed with a light-
resistant UV-lacquering. The universal VBus

®

 allows the 

parallel connection of 8 large displays as well as additional 
VBus

®

 modules. 

SD3

 

Article no.: 

180 004 93

GA3 

Article no.: 

180 006 53

AM1 Alarm module

The AM1 Alarm module is designed to signal system fai-
lures. It is to be connected to the VBus

®

 of the controller 

and issues an optical signal via the red LED if a failure has 
occurred. The AM1 also has a potential-free relay output, 
which can e. g. be connected to a building management sy-
stem (BMS). Thus, a collective error message can be issued 
in the case of a system failure. Depending on the controller 
and the sensors connected, different fault conditions can 
be signalled, e. g. sensor failures, excess or negative system 
pressure as well as errors in the flow rate, such as a dry 
run of the pump.
The AM1 Alarm module ensures that occurring failures can 
be immediately recognised and repaired, even if the system 
and the controller are difficult to access or located in a 
remote place. Thus, the reliability and the stable yield of the 
system are ensured.

AM1

 

Article no.: 

180 008 70

10.3

  Visualisation modules

The VBus

®

 / LAN interface adapter is designed for the direct 

connection of the controller to a PC or router. It enables 
easy access to the controller via the local network of the 
owner. Thus, controller access, system parametrisation and 
data charting can be effected from every workstation of the 
network. The VBus

®

 / LAN interface adapter is suitable for 

all controllers equipped with a VBus

®

. A full version of the 

ServiceCenter software is included.
VBus

®

 / USB

 

Article no.: 

180 008 50

VBus

®

 / LAN

 

Article no.: 

180 008 80 

Summary of Contents for Level 5









































































































Reviews:

No comments