background image

 

Mega ABF 40000 IL 

                           910101-001027 / 08.2019 

Page 15 of 22 

E.

 

Every Six Months 

Before beginning this maintenance procedure, carefully read the safety instructions chapter of this document and make sure that all 
the workers at the filtration site are fully aware of and comply with, these and any other local safety instructions.    

 

1.

 

Perform a General Inspection of the filter Operation as described above and carefully inspect the filter visually for: 

a.

 

Proper operation 

b.

 

Any leakage from the filter housing or accessories 

c.

 

Abnormal or unusual noises 

d.

 

Loosen bolts 

e.

 

Non smooth turning of the suction scanner 

f.

 

Unusual load on the filter electrical motor 

g.

 

Any sign of corrosion on the filter housing or accessories 

h.

 

Unusual vibrations 

i.

 

Non smooth operation of the filter valves, air release valves and check-valves 

2.

 

Close the inlet and the outlet valves of the filter. Drain the filter housing and release any residual pressure. 

3.

 

Disconnect and lock the filter's power supply. 

4.

 

Disconnect and lock the filter's compressed air supply and release any residual pressure. 

5.

 

Disassemble the filter as described in the next chapter of this document. 

6.

 

Inspect the filter screens and components for any wear and tear. 

7.

 

Check the brush assemblies. 

8.

 

Check the filter bearings. 

9.

 

Check the filter housing and lid for any sign of corrosion.  

10.

 

Check the filter internal and external coating and pain for damage  

11.

 

Replace any damaged component 

12.

 

Make sure that your maintenance engineers are aware of even the slightest sign of corrosion in the filter housing, lid or 
accessories. In such case consider performing a standard pressure vessel tests as required by your local applicable standards. 

13.

 

Re-assemble the filter as described in the next section of this document. 

14.

 

Perform a complete 

COMMISSIONING, START-UP AND FIRST OPERATION

 as described earlier in this document.    

 
 

IMPORTANT ! 

THE DRIVE SHAFT MUST BE LUBRICATED WITH HEAVY-DUTY, WATER RESISTANT GREASE THAT WILL NOT OXIDIZE. (SHELL, 
DARINA EP-2 OR SIMILAR)

 

 

 

Summary of Contents for MEGA ABF 40,000























Reviews: