manualshive.com logo in svg

amiad Filtomat MG112, Installation, Operation And Maintenance Instructions

Share
Download
amiad Filtomat MG112 Installation, Operation And Maintenance Instructions Download Page 25

 

MG112

 

                         910101-000516 / 06.2019 

Page 25 of 31 

 
Dirt Collector - Parts Schedule  
 

No. 

CAT No.  

DESCRIPTION 

Qty. 

Material 

1 

710103-000920 

Body Dirt Collector S/St304 (6 Noz) 

1 

S/ST 304 

2 

700190-001608 

NOZZLE CLAMPS (A)OD52 STD M10XXL 

 

Various 

2.1 

760102-000097 

NYLON INSERT LOCKNUT 1/4"UNC S/ST316 DIN985 

12 

S/ST 316 

2.2 

710101-000693 

Nozzle Suction OD52 Dirt Colllector  

12 

NYLON 

2.3 

710101-000704 

Nozzle Suction Oval Clamped 

6 

NYLON 

2.4 

760101-000688 

Phillips Pan Tap Screw #8x3/8" S/St316 

12 

S/ST 316 

3 

710103-010021 

CONNECTOR M100 BRASS F/DIRT COLLECTOR 

1 

Brass 

4 

710103-000800 

Central Support Collector 

1 

NYLON 30%GF 

5 

710103-001483 

Shaft Dirt Collector M-X04L/8L(P) Brass 

1 

Brass 

6 

710103-000802 

Upper Plug Collector 

1 

NYLON 30%GF 

7 

760101-000417 

 Hex Bolt Partial Thread 1/4"UNCX1 1/4" S/ST304 

12 

S/ST 304 

8 

710103-000942 

Body Bottom F.Screen F M1XX PVC Piston 

1 

PVC 

9 

710103-000989 

ROTOR (A) M1XX(C(X(L(P 304, NYLON ASSY. 

1 

VARIOUS 

9.1 

710103-000809 

Rotor Nylon 6/6 M104LP-M110P 

1 

NYLON 

9.2 

760101-000426 

 Hex Bolt full Thread 5/16"UNCX1" S/ST304 

7 

S/ST 304 

9.3 

710103-001088 

Housing Bearing Rotor Brass 

1 

Brass 

9.4 

710103-001333 

 Lower Bearing Male 

1 

K110 

Summary of Contents for Filtomat MG112
































Reviews:

No comments

Brands by name

Popular brands

Load more brands