manualshive.com logo in svg

amiad Filtomat M100, Installation, Operation And Maintenance Instructions, Page: 22 / 31

Share
Download
amiad Filtomat M100 Installation, Operation And Maintenance Instructions Download Page 22

 

M104LPN, M106LP Electronically Controlled                    910101-000484 / 12.2019 

Page 22 of 31 

 

Parts Schedule M104LPN- M106LP Electronic Models 

 

No. 

CAT No.  

DESCRIPTION 

Qty. 

Material 

1 

710105-XXXXXX 

M104LPN FILTER HOUSING RAL5010 PLOYESTER  

1 

ST.37-2 

710105-XXXXXX 

M106LP FILTER HOUSING RAL5010 PLOYESTER  

 

 

2 

770102-000174 

PARKER O-RING 2-448 NBR 70 SHORE 

2 

NBR 

3 

700190-001541 

COVER ASSY CAST-IRON W/PIS AND VALVE PISTON MOD 

1 

Various 

4 

760104-000075 

STUD BOLT 1/2" UNC 50MM S/ST303 

15 

S/ST 303 

5 

760103-000077 

FLAT WASHER M12 DIN125 C/ST ZINC PLATED 

16 

Zinc Plated 

6 

760102-000052 

HEX NUT 1/2"UNC C/ST ZINC PLATED B18.2.2 

16 

Z.PLATED C/ST 

7 

730110-000009 

3/8" ACCELERATOR DOROT PLASTIC BLACK W/GREEN SPRING 

1 

PLASTIC 

8 

780101-000611 

REDUCER 2"X1 1/2" PP PLASSON 

1 

PP 

9 

700190-001508 

DIRT COL.A 4NOZ.+ ROTOR AND PART M104LP/106LP ASSY 

1 

Various 

10 

700101-002073 

MOLDED WEAVEWIRE SCREEN S/ST316L 6150SQ.CM 130MIC M100 NBR SEALS 

1 

VARIOUS 

10.1 

770102-000217   DOWTY O-RING SEAL 674 ID=208.92MM TH=6.99MM NBR 55 SHORE NO FLASH 

1 

 NBR  

11 

700190-004630 

INJECTED COARSE SCREEN ASSEMBLY M104/6 LP/XLP 

1 

PP+40% GF 

12 

710105-000362 

M104/6LP COVER PKPK 5010 ST.37-2 POLYESTER 

1 

ST. 37-2 

13 

760104-000081 

STUD BOLT 1/2" UNC 92MM S/ST304 

1 

S/ST 304 

14 

760190-000666 

RUBBER BOLT COVER 1/2" BLACK 

1 

Rubber 

15 

900102-000318 

LABEL GENERAL DANGER CLEAR PVC BLACK/YELLOW 75X85MM ACRILIC SILK 

1 

NA 

16 

700103-001763 

ADI-P DC KIT PACKAGE ONE SOLENOID NC 

1 

Various 

700103-001764 

ADI-P DC KIT PACKAGE TWO SOLENOIDS NC 

 

 

17 

760105-000036 

RIVET BLIND 3X6MM S/ST316 DIN7337 

4 

S/ST 316 

18 

730108-000120 

AIR RELEASE VALVE A.R.I BARAK D-040-P 1" BSPT NYLON3 16BAR W/3/8" DRAIN OUT 

1 

 PP 

19 

720501-000172 

L-CONNECTOR 3/8"M X12MM BSPT ACETAL BLACK TEFEN 

3 

PP Copolymer 

20 

720501-000229 

L-CONNECTOR 1/4"M X8MM BSPT ACETAL BLACK-BLUE TEFEN 

2 

NYLON 

21 

720501-000217 

L-CONNECTOR 3/8"M X8MM BSPT RPP BLACK-BLUE TEFEN 

1 

PP 

22 

720501-000190 

PLUG 1/4"M BSPT PA66 BLUE TEFEN 

3 

PVC 

23 

720501-000243 

STRAIGHT CONNECTOR 1/8"M X8MM BSPT RPP BLACK-BLUE TEFEN 

1 

PP 

24 

700190-005809 

ADI-P DC 1 BACSOL 12VDC 2W LATCH 8MM TEFFEN M104/6/8/10 LP/XLP ASSY 

1 

VARIOUS 

25 

720502-000021 

CONTROL TUBE 12MM LDPE BLACK TEFFEN 

1 

PA 

26 

720502-000017 

CONTROL TUBE 8MM LDPE BLACK W/GREEN STRIPE TEFFEN 

2 

PA 

 

 

 

 

 

Summary of Contents for Filtomat M100
































Reviews:

No comments