SERIES 925 (A1 & A2)
INSTALLATION & SERVICE BULLETIN
1080 N. Crooks Road, Clawson, MI 48017-1097
Phone (248) 435-0700 FAX (248) 435-8120
For Sales & Technical Assistance Call 800-635-0289
A Product of
FORM1054
Rev. B
5/1/03
The instructions that follow are intended for
use with the 925 A1 and 925 A2 models.
They also are to be used for all outputs
whether Patriot Sensors & Controls resolver,
potentiometers, encoders, or customer
resolvers. The latter will also have additional
installation instructions.
INSTALLATION:
The 925 may be mounted in any position,
except for the two shown in
Fig. 1
(Please
note the qualifier for the two positions.)
5/16”
dia. bolts are the preferred choice for
securing the unit to the base to which it is
mounted.
Fig. 1
Positions not recommended
without external cable support.
Cable attachment is with the .19” dia. pin
provided on the cable end assembly. The
rubber bumper on the cable serves as a stop
for initial cable tension. The 925 unit is
shipped with the correct spring tension
applied (see
Important Note
under
SPRING
TENSION ADJUSTMENT
section for
information regarding spring tension). If
spring adjustment is absolutely necessary,
please see
SPRING TENSION
ADJUSTMENT
for proper tension adjusting
instructions.
If the 925 was ordered with initial cable lead,
the length will be marked with a steel clip.
Do
not
remove the top cover during installation.
If the unit has a standard Patriot Sensors &
Controls resolver installed, an input
connector plug (see drawing #
SD0296000
) is
included along with a wiring diagram (see
drawing #
SD0308900
) for the multiconductor
cable.
CABLE REPLACEMENT:
TOOLS REQUIRED:
5/64” ALLEN WRENCH
FLAT BLADE SCREWDRIVER
1) Remove the top cover and release spring
tension, if any (see
SPRING TENSION
ADJUSTMENT
section ). Between the top
cover and the spring housing there is an
access hole
(see
Fig. 2)
.
Fig. 2
Location of screw access hole.
Rotate the drum until the end of a button
head socket screw appears (by looking
through the access hole). Remove this screw
with the Allen wrench (
NOTE:
Care must be
taken when removing the screw so as to
prevent the screw from falling off inside the
enclosure). Pull all remaining cable free from
the drum.
2) The new cable end should lay in the
machined pocket on the drum
(see
Fig. 3)
.
Re-insert screw through cable end eye and
into threaded hole on drum with Allen wrench
and tighten.
Fig. 3
Location of pocket on cable
drum.
Test the integrity of the cable anchor by
tugging on the cable once or twice.
3) To wind the new cable on the drum easily,
the recoil springs(s) should be disconnected
from the drum shaft. See
SPRING TENSION
ADJUSTMENT
section for instructions on
how to disconnect the spring(s).
4) After the spring(s) have been
disconnected, rotate the drum until all the
cable has been stored. Make sure that the
cable is fed into the first drum groove
correctly. If not, the cable will interfere with
the cable guide (gray steel bar across drum)
and affect the operation of the unit.
5) Adjust spring tension (see item 3 under
SPRING TENSION ADJUSTMENT
) and then
reassemble the rest of the 925 unit.
SPRING TENSION ADJUSTMENT
and REPLACEMENT
:
TOOLS REQUIRED:
3/32” ALLEN WRENCH
SMALL FLAT BLADE
SCREWDRIVER
Important Note:
The following instructions should be used
only after repair or other remedial attention
has been given to the 925. Tension adjusting
is
not
necessary at the time of initial
installation since the proper tension has been
set before shipment. Increasing spring
tension is not the answer to erratic recoil
action since it only serves to mask the real
problem. Increasing spring tension decreases
cycle life. Carried to the extreme, it will pull
the cable out of the cable anchor, break the
spring through overload, or some similar
failure.
These types of failures are not
covered by the warranty.
1) For safety reasons, all spring tension
adjustments should be conducted with the
cable retracted on the drum. At this time the
stored energy is at a minimum.
2) Loosen two of the three servo clamp
screws with the Allen wrench
(see
Fig. 4)
.
Grasp the spring housing firmly while
loosening the third screw. Relax any residual
tension. If spring removal and installation is
not required, refer to Item 3 of this section for
remaining tension adjustment instruction.
3) With the three servo clamp screws
installed, but not tightened, the cast
aluminum spring housing for the A1 model
and the plastic housing of the A2 should be
grasped firmly and rotated
clockwise.
The
rotation is 10 turns for the A1 and 15 turns for
the A2 model. Secure the three servo clamp
screws.
SPRING REMOVAL: A1
The spring housing assembly may be freed
by removing all three servo clamp screws.
Grasp spring cover, which is an aluminum
casting, and pull cover and spring free from
drum shaft roll pin
(see
Fig. 4)
. (
CAUTION:
Cover and spring must be removed together
as
one
unit.) Spring may now be removed
for inspection or replacement by
disconnecting spring tang from the cover.
CAUTION:
On reassembly, make sure hook
tang faces the same direction that it did at
disassembly.
