Amersham Biosciences AKTA design P-960 User Manual Download Page 8

1

Introduction

8

Pump P-960

 User Manual 18-1172-73 Edition AA

1.2

Safety

The unit is designed for indoor use only.

Do not use in a dusty atmosphere or close to spraying water.

Do not block the outlet of the unit.

 

 

  

  

  

WARNING!

 

HAZARDOUS CHEMICALS.

 When using hazardous 

chemicals, all suitable measures, such as wearing protective glasses, 
must be taken.

WARNING!

 

CORROSIVE CHEMICALS.

 NaOH is corrosive and 

therefore dangerous to health. Avoid spillage and wear protective 
glasses.

WARNING! HAZARDOUS CHEMICALS.

 Incorrectly fitted tubing 

might loosen, causing a jet of liquid to spray out. This is especially 
dangerous if hazardous chemicals are being used. Connect the 
tubing by first inserting the tubing fully, then tightening the connector 
fingertight.

CAUTION! 

The mains power to the ÄKTAdesign chromatography 

system must be switched OFF before connecting the unit to the 
UniNet-2 link.

CAUTION!

 Always disconnect the UniNet-2 connectors before 

attempting to replace any item on the unit.

CAUTION! 

Before the start of each run, always ensure that there is an 

adequate supply of eluent in the reservoir. Avoid pumping without 
liquid, since this might affect the lifetime of the sealing parts in the 
pump.

18117273aa.book  Page 8  Thursday, July 3, 2003  5:13 PM

Summary of Contents for AKTA design P-960









































Reviews: