Ameriwood HOME 4566926COM Manual Download Page 1

Page: 1 / 43

4566926COM

Media Dresser

B344566926COM00MP

THIS INSTRUCTION BOOKLET CONTAINS

IMPORTANT

SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Follow Ameriwood Home

Tube

You

Date of Purchase ___ / ___ / ___

Lot Number:

Do Not Return This Product!

Contact our customer service team for help rst.

Call:

1-800-489-3351 (toll free)

Monday-Friday 9am - 5pm CST

Visit:

www.ameriwoodhome.com

Assembly Di culty Meter

Easy

Tough

Secure Your Furniture

Keep your home and family safe

with the wall anchor kit that is

included with the product.

Serious or fatal crushing injuries can

occur from

g furniture.

WARNING: Manufacturer assumes no liability

for improper

on or excessive loads

placed on screws or bracket. This wall anchor

is not a subs tute for proper adult supervision.

Summary of Contents for 4566926COM












































Search results

Summary of Contents for 4566926COM

Reviews:

Related manuals for 4566926COM

Brands by name

Popular brands

Ameriwood HOME 4566926COM, Manual

Search results

Summary of Contents for 4566926COM

Reviews:

Related manuals for 4566926COM

Brands by name

Popular brands