background image

2904

Certified to comply with ANSI A112.18.1

Installation

Instructions

Centerset Lavatory Faucet with

Speed Connect™ Drain 

Adjustable Wrench

 Screwdriver

Channel Locks

Recommended tools

Tubing Cutter

1

INSTALL FAUCET

SINK OR

MOUNTING

SURFACE

POP-UP

CABLE

Turn off hot and cold water supplies before beginning.

Insert FAUCET 

(1)

 and CABLE CONNECTOR 

(2)

 through

mounting holes of Sink or mounting surface. 

Fig.

 

A.

Assemble LOCKNUTS 

(3)

 onto SHANKS 

(4)

 ( from under

side of Sink. Hand tighten firmly. 

Fig.

 

B.

 

2

2

4

3

3

4

Turn off hot and cold water

supplies before beginning.

CAUTION

(HAND TIGHTEN)

T M

M 9 6 8 4 2 3   R e v . 1 . 2

Fig.

 

A.

Fig.

 

B.

1

Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

*Your new American Standard faucet is designed to work only with the Speed Connect drain. Helpful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.

Speed Connect Drain*

•  1/3 of the parts, installs in 1/3 of the time
•  No tools needed
•  Never needs adjustment
•  Guaranteed to seal properly the first time, every time.

Summary of Contents for Williamsburg 2904








Reviews: