background image

2808.222

2908.222

T M

4

6

5

SLOT

MOUNTING

SURFACE

Insert SPOUT 

(1)

 and CABLE CONNECTOR 

(2)

 through center hole, making sure

the SEAL WASHER 

(3)

 is properly seated in SPOUT 

(1)

.

Assemble RUBBER WASHER 

(4)

, BRASS WASHER 

(5)

 and LOCKNUT 

(6)

 onto SPOUT

SHANK 

(7)

 from under side of sink . Make sure SPOUT 

(1)

 is centered in the mounting

hole and the slot in the BRASS WASHER 

(5)

 faces toward the rear of the sink.

Tighten LOCKNUT 

(6)

 firmly. 

Fig. A.

Hand tighten LOCKNUT 

(11)

 to secure VALVE BODY 

(12)

.

Repeat above steps for opposite VALVE BODY 

(12A)

.

Install LOCKNUT 

(11) 

onto VALVE BODY 

(12)

.

From under side of mounting surface, install VALVE BODY 

(12)

 through valve

mounting holes. Threads of VALVE BODY 

(12)

 should extent at least 5/16

of a inch above mounting surface top. 

Fig. B.

Important: 

Thread ESCUTCHEON 

(10)

 onto VALVE BODY 

(12)

 until snug against

internal stop. This is key to the installation. If not done, the faucet handles won’t
work correctly. If necessary, adjust LOCKNUT 

(11)

.

1

1A

Certified to comply with ANSI A112.18.1

Installation

Instructions

INSTALL SPOUT

INSTALL VALVE BODY

2

10

9

11

12

12a

10

9

12

11

3

Place RUBBER RING 

(9)

 into ESCUTCHEON 

(10)

.

5/16'' MIN.

7

Adjustable Wrench

 Screwdriver

Channel Locks

 Recommended tools

Tubing Cutter

Fig.

 

B.

1

U S 6 0 3 8 5   R e v.   1 . 2

W idespread Lavatory Faucet with the

Speed Connect™ Drain 

*Your new American Standard faucet is designed to work only with the Speed Connect drain. Helpful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

1

Fig.

 

A.

1

2808 SERIES

Congratulations on purchasing your American Standard faucet with
the Speed Connect Drain,  a feature found only on 
American Standard faucets.

Speed Connect Drain*

•  1/3 of the parts, installs in 1/3 of the time
•  No tools needed
•  Never needs adjustment
•  Guaranteed to seal properly the first time, every time.

Turn off water at

main supply.

CAUTION

Summary of Contents for Williamsburg 2808.222

Page 1: ...et handles won t work correctly If necessary adjust LOCKNUT 11 1 1A Certified to comply with ANSI A112 18 1 Installation Instructions INSTALL SPOUT INSTALL VALVE BODY 2 10 9 11 12 12a 10 9 12 11 3 Place RUBBER RING 9 into ESCUTCHEON 10 5 16 MIN 7 Adjustable Wrench Screwdriver Channel Locks Recommended tools Tubing Cutter Fig B 1 US60385 Rev 1 2 Widespread Lavatory Faucet with the Speed Connect Dra...

Page 2: ... COVER 1 Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 Fig A 2 REAR OF SINK 4 5 6 3 1 SINK DRAIN HOLE FLAT SIDE OF GASKET MUST FACE DOWN 1 2 Fig A 2 1 FLAT SIDE OF GRAY LOCKNUT MUST FACE UP INSTALL GRAY LOCKNUT 5 Install GRAY LOCKNUT 1 onto DRAIN BODY 2 from below SINK Fig A Note The flat side of the GRAY LOCKNUT 1 must face up Tighten firmly by hand No tools are required Check DRAIN FLANGE ...

Page 3: ...TER SUPPLY AND WASTE CONNECTIONS NOTE FLEXIBLE SUPPLIES OR BULL NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY HOT COLD FERRULE COMPRESSION NUT COUPLING NUT FLEXIBLE SUPPLIES 1 1A 3 8 O D BULL NOSE RISERS 1 2 PIPE THREAD 3 8 COMPRESSION CONNECTION 2 3 4 5 7 6 6A 7A Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig A Your new POP UP DRAIN installation i...

Page 4: ...Thread HANDLE BASE 3 onto VALVE ESCUTCHEON 7 Push LEVER BALL 4 onto ADAPTER 1 Push ADAPTER 1 on VALVE STEM 2 so that the hole of the ADAPTER 1 without spline is facing up INSTALL HANDLES 6 INSTALLATION OF OPTIONAL METAL LEVER HANDLES Supplied with Faucet Thread PORCELIAN LEVER HANDLE 2 counter clockwise and remove INDEX BUTTON with MOUNTING ROD ASSEMBLY 1 Insert MOUNTING ROD ASSEMBLY 1 into METAL ...

Reviews: