American Standard Town Square T555740 Installation Instructions Manual Download Page 1

M962636-YYY0A

VOLUME CONTROL HANDLE

T555740

TOWNSQUARE

TOWNSQUARE

Installation

Instructions

M 9 6 8 6 5 9

M 9 6 8 6 5 9

M 9 6 8 6 5 9

M 9 6 8 6 5 9

Thank you for selecting American-Standard...the benchmark

of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

Certified to comply with ANSI A112.18.1M
ASSE 1016

ROUGHING-IN DIMENSIONS

MODEL NUMBER

CHROME

BLACKENED BRONZE (PVD)

SATIN NICKEL (PVD)

002

068

295

Replace the "YYY" with

appropriate finish code

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1-800 442-1902

Weekdays 8:00 a.m. to 8:00 p.m. EST

IN CANADA  1-800-387-0369   (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

Product names listed herein are trademarks of American Standard Inc.

Recommended Tools

Flat Blade Screwdriver

Phillips Screwdriver

Remove as much surface dirt and film using clear 

water and soft cotton cloth (as described above).

 

     Use any of the following to remove tough surface 

     film and build-up:

     Mild liquid detergents

     Clear ammonia free liquid glass cleaners

     Non-acidic, non-abrasive gentle liquid or fully

     dissolved powder cleansers mixed according to

     manufacturers directions.

     Non-abrasive liquid polishers

Once clean, rinse faucet again with clear water to 

thoroughly remove cleaner or polish and blot dry with

a soft cotton cloth. 

To keep your new faucet looking new, please follow

these simple care instructions:

DO:     Simply rinse the faucet clean with clear water.

           Dry the faucet with a soft cotton cloth.

DO NOT: 

           Do not use any abrasive cleaners, cloths, or 

           paper towels.

           Do not use any cleaning agents containing

           acids, polish abrasives, or harsh cleaners or

           soaps.

Regular and routine cleaning will reduce the need for

heavy cleaning and polishing. If heavy cleaning is

required, the following procedures are recommended:

CARE INSTRUCTIONS:

Failure to follow these care instructions may

damage the Faucet's finish.

A907090-YYY0A

CAP

1

Remove PLASTER GUARD (1) if attached.

Push CAPS (2 & 2a) as shown onto CONTROL

VALVES (3).

Push ESCUTCHEON (4) over CAPS (2, 2a) and

flush against finished wall. Attach with the two

SCREWS (5) provided.  

4

4

4

TEMPERATURE ADJUSTMENT

SET HOT LIMIT STOP

Check that arrow marking B points to the 3 o'clock position. If not, push the BLACK CLAMP on the SECURING RING to

the right, pull off KNOB MOUNT (4) and reinstall KNOB MOUNT (4) with arrow "B" 3 o'clock position. 

See Figure 1.

For 100˚F adjustment, turn the water supply on. Turn KNOB MOUNT (4) until the spout temperature is 100˚F. Check

that arrow "A" on the KNOB MOUNT (4) still points 3 o'clock position after adjusting the thermostat to 100˚F.

If not, pull out the RED LOCKING DEVICE. Remove KNOB MOUNT (4) by pulling it towards you while standing directly in

front of the valve.

Reinstall the KNOB MOUNT (4) with arrow "A" 3 o'clock position.

The maximum mixed water temperature is set at 109˚F at the factory. This setting can be changed if desired.

Remove the TEMPERATURE LIMIT STOP (H shaped Black Plastic part). Reinstall it at the desired notch as indicated in

the diagram to limit the maximum mixed water temperature to 104˚F or 112˚F.

Reinstall RED LOCKING DEVICE.

See step 3 for HANDLE (3) installation.

Pull out index CAP (1) and remove HANDLE SCREW (2). Pull off HANDLE ASSEMBLY (3).

ARROW

"A"

BLACK

CLAMP

ARROW

"B"

RED LOCKING

DEVICE

TEMPERATURE

LIMIT STOP

ARROWS AT 3 O'CLOCK

POSITION

Figure 1

KNOB MOUNT

112 

109 

104 

1

TRIM INSTALLATION

2

INSTALL HANDLES

Should the hot and cold water supply pipes have been transposed making

adjustment impossible, proceed as follows:

TRANSPOSED SUPPLY PIPING

OR BACK TO BACK INSTALLATION

3

Remove check stops and re-install them transposed.

Shut off water supply.
Remove handle and rim. (Reverse steps 1 and 2.

CHECK STOP

(RED TO BLUE)

Turn the water supply back on and perform the temperature adjustment in step 4.
Assemble HANDLES and TRIM.

CHECK STOP

(BLUE TO RED)

Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE

CHECK STOP is now on the left.

CENTRAL THERMOSTAT

WITH VOLUME CONTROL

TRIM KIT

1

8

1

5

9

10

11

3

4

6

2

2a

3

TOP

 

1

5

7

Align HANDLE BASE (1) and push onto KNOB MOUNT (2).

Install LEVER HANDLE (3) as shown. Install HANDLE SCREW (4) and

tighten with screwdriver.

Push INDEX CAP (5) into HANDLE (3).

Install HANDLE ADAPTER (6) onto VALVE STEM (7).

Install HANDLE SCREW (8) and tighten.

Push VOLUME CONTROL KNOB (9) onto HANDLE ADAPTER (6).

Use HEX WRENCH (10) supplied and tighten set screw to secure 

VOLUME CONTROL KNOB (9).

Push in PLUG BUTTON (11)

2

M962635-YYY0A

ESCUTCHEON AND SCREWS

A918434-YYY0A

ESCUTCHEON SCREWS

M962633-YYY0A

HANDLE SCREW

AND INDEX BUTTON

M908587-YYY0A

HANDLE BASE

M916815-YYY0A

LEVER HANDLE

© AS America, Inc. 2007

CENTRAL THERMOSTAT

WITH VOLUME CONTROL

TRIM KIT

186mm

(7-3/8)

100mm

(3-7/8)

230mm

(9)

230mm

(9)

48mm to 68mm

(2 to 2-5/8)

150mm

(6)

NOTE: FITTING 

MUST BE INSTALLED

WITH VOLUME CONTROL 

ON TOP.

R520

1/2" NPT INLETS

or

R540

3/4" NPT INLETS

25mm

(1)

FINISHED

WALL

190mm

(7-1/2)

4

2

3

T555740

Summary of Contents for Town Square T555740











Reviews: