4
6
14
5
SLOT
MOUNTING
SURFACE
Turn off hot and cold water
supplies before beginning.
CAUTION
Insert SPOUT (1) and CABLE CONNECTOR (14) through center hole, making sure
SEAL WASHER (2) is properly seated in SPOUT BASE (3).
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT
SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting
hole and the
slot
in the BRASS WASHER (5) faces toward the rear of the sink.
Tighten LOCKNUT (6) firmly. Fig. A.
Tighten LOCKNUT (11) with WRENCH (8) (supplied) to secure VALVE
BODY (13). Repeat above steps for opposite VALVE BODY (13A).
Install LOCKNUT (11) and RUBBER WASHER (12) onto VALVE BODY (13).
From under side of mounting surface, install VALVE BODY (13) through valve
mounting holes. Threads of VALVE BODY (13) should extent at least 5/16
of a inch above mounting surface top. Fig. B.
Thread DECK ADAPTER (10)
onto VALVE BODY (13) until snug against internal stop. If necessary, adjust
LOCKNUT (11).
1
1A
Certified to comply with ANSI A112.18.1
Installation
Instructions
Spread Lavatory Faucet
with Speed Connect™ Drain
INSTALL SPOUT
INSTALL VALVE BODY
1
2
1
8
10
9
12
11
13
13a
10
9
12
11
3
Place RUBBER RING (9) into DECK ADAPTER (10).
13
5/16'' MIN.
7
Adjustable Wrench
Screwdriver
Channel Locks
Recommended tools
Tubing Cutter
Connect HOT water supply to inlet of left SHANK and COLD
water supply to right SHANK using sealant, appropriate
connectors, and COUPLING NUTS.
Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to
waste outlet.
Thread TEE BODY (4) to SPOUT SHANK (5).
Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, 7A).
9
Connect water supply to VALVE BODIES (1,1A) with 1/2" IPS FLEXIBLE
SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use
adjustable wrench to tighten connections. Do not over tighten.
Be careful not to kink copper supply when bending. Use tubing
cutter to cut to proper length.
MAKE WATER SUPPLY AND WASTE CONNECTIONS
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED
AND MUST BE PURCHASED SEPARATELY.
HOT
COLD
FERRULE
COMPRESSION
NUT
COUPLING
NUT
FLEXIBLE
SUPPLIES
1
1A
3/8 O.D.
BULL-NOSE
RISERS
1/2" PIPE THREAD
3/8 COMPRESSION
CONNECTION
2
3
4
5
7
6
6A
7A
Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten.
Fig.
A.
Your new POP-UP DRAIN installation is
now complete.
Fig.
B.
Note:
Tailpeice on pop-up drain is 1-1/4” O.D.
Fig.
B.
Fig.
A.
ATTACH CABLE CONNECTOR
7
2
1
Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes.
Note: If STOPPER (2) does not open and close properly then refer
to the “troubleshooting section” of these instructions.
CHECK OPERATION OF POP-UP
8
Fig.
B.
1-1/4” O.D.
Speed Connect™ Drain
Troubleshooting Guide
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise.
Fig.
A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration.
Fig.
B.
Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain.
Fig.
D.
Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal.
Fig.
E.
The Stopper can now be removed by lifting it out of the Drain.
Fig.
F.
CAM
CAM CAP
CABLE ADJUSTMENT PROCEDURE
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
Fig.
B.
Fig.
A.
REMOVE
CAM
Fig.
E.
Fig.
F.
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise.
Fig.
A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration.
Fig.
B.
Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position.
Fig.
B, C.
Push DOWN on the Lift-Knob to make sure it is fully down.
Fig.
C.
Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten.
Fig.
A.
STOPPER REMOVAL PROCEDURE
STOPPER INSTALLATION PROCEDURE
Locked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper.
Fig.
G.
To install the stopper in
“Locked”
mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the
rear
of the
Sink and the American Standard logo is facing
front
. Rotate
Stopper slightly if necessary so that the Stopper slides all the
way down.
Fig.
G.
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted.
Fig.
J.
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted.
Fig.
K.
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
Troubling Shooting Guide to complete installation. Stopper will be
in
“Locked”
mode and not be removable.
Unlocked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper.
Fig.
H.
To install the stopper in
“Unlocked”
mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the
front
of the
Sink and the American Standard logo is facing
rear
. Rotate Stopper
slightly if necessary so that the Stopper slides all the way down.
Fig.
H.
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted.
Fig.
J.
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted.
Fig.
K.
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troublingshooting Guide” to complete installation. Stopper will be
in
“Unlocked”
mode and removable
.
Fig.
J.
Fig.
K.
INSTALL
CAM CAP
CAM
INSTALL CAM
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be
removed) or “Unlock” Mode (Stopper is removable).
Unlocked Mode
Fig.
A.
Fig.
B.
1
2
LOOP TOWARD
FRONT OF SINK
180˚
LOGO
DRAIN
Fig.
H.
Locked Mode
(Vandal Proof)
LOGO
DRAIN
Fig.
G.
LOOP TOWARD
REAR OF SINK
2
1
RE-ATTACH
DISCONNECT
Fig.
D.
REMOVE
CAM CAP
Fig.
C.
DOWN
STOPPER
072574-0070A
EXTENSION ROD
066116-YYY0A
DRAIN STOPPER
M961711-0070A
TAILPIECE INSERT
070847-0070A
CLIP
066118-0070A
PIVOT ROD KIT
M953450-YYY0A
COMPLETE
DRAIN ASSEMBLY
070532-0040A
TAILPIECE
066117-YYY0A
2" FLANGE KIT
POP-UP DRAIN ASSEMBLY
BEFORE 01/07
1
7
3
5
6
M 9 6 8 7 8 7 R e v. 1 . 3
M 9 6 8 7 8 7 R e v. 1 . 3
M 9 6 8 7 8 7 R e v. 1 . 3
M 9 6 8 7 8 7 R e v. 1 . 3
M 9 6 8 7 8 7 R e v. 1 . 3
M 9 6 8 7 8 7 R e v. 1 . 3
M 9 6 8 7 8 7 R e v. 1 . 3
WIDESPREAD
LAVATORY FAUCET
MODEL NUMBER
911836-0070A
SEAL
024220-0070A
SUPPLY NUT
M962623-YYY0A
LIFT ROD
M961732-YYY0A
LIFT ROD
2555.801
2555.801
TOWNSQUARE
TOWNSQUARE
M953006-0070A
TEE & HOSE KIT
CHROME
002
POLISHED BRASS
099
SATIN NICKEL 295
Replace the "YYY" with
appropriate finish code
066070-YYY0A
AERATOR
M961729-0070A
FRICTION NUT
AND RING
M916807-YYY0A
LEVER HANDLE
M962104-YYY0A
HANDLE BASE KIT
994053-0070A
CARTRIDGE
M961634-0070A
VALVE MOUNTING KIT
M918305-0070A
HANDLE SCREW
M918025-0070A
HANDLE ADAPTER
M961730-0070A
DECK ADAPTER KIT
M961731-YYY0A
SPOUT KIT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© AS America Inc. 2007
M907024-YYY0A
INDEX BUTTON
(HOT & COLD)
M961733-0070A
SPOUT
MOUNTING KIT
1
IN MEXICO 01-800-839-12-00
Thread FLANGE (1) counter-clockwise and remove
FLANGE (1) and FOAM GASKET (2) from drain
body. Fig. A.
Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3). Fig. B.
POP-UP DRAIN
Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY. Fig. B.
2
4
3
2
TIGHTEN LOCKNUT
1
REMOVE FLANGE
Remove CLEAR PLASTIC COVER (1).
Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).
2
2
3
3
1
1
Tighten LOCKNUT (1) firmly with Adjustable
Wrench or Channel Locks.
INSTALL DRAIN FROM
BELOW FIXTURE
5
From under side of SINK
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.
Install FOAM GASKET (3) and
FLANGE (4) onto drain body
from above SINK and tighten
FLANGE (4) firmly.
4
Fig. A.
Fig. B.
Fig. A.
Fig. B.
2
DRAIN
OUTLET
1
3
4
REAR OF SINK
DRAIN
BODY
4
6
1
POP-UP KNOB (1) must be fully down.
Fig.
B.
FLANGE GASKET AND POP-UP KNOB
DOWN
WHITE FOAM
GASKET
NOT VISIBLE
DRAIN
FLANGE
Fig.
A.
Fig.
B.
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible.
Fig.
A.
CHECK DRAIN CONNECTIONS
11
10
12
TEST INSTALLED FITTING
With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2)
and check all connections for leaks.
Remove AERATOR (3).Operate both HANDLES (1) to flush water
lines thoroughly.
Replace AERATOR (3).
1
HOT
COLD
2
4
2
1
5
“P” TRAP
WASTE
OUTLET
Operate POP-UP KNOB (5) and fill Sink with water. Check that DRAIN
STOPPER (4) makes a good seal and retains water in Sink. If STOPPER
(4) does not seal properly, please refer to “Troubleshooting Guide” in
these instructions.
Release POP-UP KNOB (5) down and check all drain connections and
"P" trap for leaks. Tighten if necessary.
4
INSTALL HANDLES
13
14
SERVICE
To change direction of handle rotation,
proceed as follows
:
Turn valve to OFF position. See step 11 and
reverse to remove HANDLE ASSEMBLY (1).
Remove SPRING CLIP (2). Lift STOP
WASHER (3), turn 90
°
and replace.
Replace SPRING CLIP (2).
See step 11 for replacing HANDLE
ASSEMBLY (1).
1
2
3
4
5
6
7
10
Figure A
Figure B
Figure C
Figure D
8
Turn VALVE to OFF position.
Figure A: Install STEM ADAPTERS (7) onto VALVE STEMS (8).
Figure B: With colored side up, place FRICTION RING (6) over DECK ADAPTER (10). Loosely screw FRICTION NUT (5)
onto DECK ADAPTER (10). Do not tighten. Align flats on FRICTION NUT (5) with RIBS (9) in HANDLE BASE (4).
Figure C: Screw HANDLE BASE (4) with FRICTION NUT (5) onto DECK ADAPTER (10) until snug against mounting
surface and aligned properly.
Figure D: Install LEVER HANDLE (3) onto HANDLE ADAPTER (7) and align. Check alignment, if not satisfactory remove
and align. Insert HANDLE SCREW (2) and tighten. Press in INDEX BUTTON (1).
1
2
3
90°
6
10
5
9
4
FLATS
4
5
10
ALIGNED
3
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Speed Connect™ Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
M962552-0070A
CAM ASSEMBLY
M952430-0070A
CABLE ASSEMBLY
M952425-YYY0A
DRAIN ASSEMBLY
M962544-YYY0A
STOPPER
ASSEMBLY
M962457-YYY0A
FLANGE
ASSEMBLY
M962458-0070A
DRAIN MOUNTING KIT
A919661-0020A
TAILPIECE
M922872-0070A
CAM SEAT INSERT
M913207-0070A
TAILPIECE INSERT
M919660-0020A
6” TAILPIECE
(NOT INCLUDED
WITH FAUCET)
DO: SIMPLY RINSE THE PRODUCT
CLEAN WITH CLEAR WATER.DRY
WITH A SOFT COTTON FLANNEL
CLOTH.
DO NOT: DO NOT CLEAN THE
PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH
CLEANERS, OR A CLOTH WITH
A COARSE SURFACE.
CARE INSTRUCTIONS:
