background image

M965652 (11/14)

CAUTION:

  Use only American Standard 

supplied cable sets. Using non-AS supplied 
cables, or cutting, splicing or modifying any 
components will void the warranty.

CAUTION:

  Use only American Standard 

supplied cable sets. Using non-AS supplied 
cables, or cutting, splicing or modifying any 
components will void the warranty.

Installation Instr

uctions

In

s

ta

ll

a

ti

o

n

 I

n

s

tr

u

c

ti

o

n

s

Certified to comply with ASME A112.18.1

© 2014 American Standard

NOTE TO INSTALLER: Please give this manual to the customer after installation.

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

®

 Products visit our website at: 

www.americanstandard-us.com

or e-mail us at: 

[email protected]

For Parts, Service, Warranty or other Assistance,

please call

 

(844) CRT-TEAM / (844) 278-8326  

(In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

SELECTRONIC

®

Hard-Wired AC Powered 

Innsbrook Lavatory 

Proximity Faucet

Product No.'s & Options

Specifications

Faucet Installation

Electrical Installation

Start-up / Maintenance

FAQ’s / Troubleshooting

Parts

1

2

2-3

4-6

7-9

9-10

11

MODEL NUMBERS

605X.202  605X.204  605X.205

Summary of Contents for SELECTRONIC 605X.202












Reviews: