manualshive.com logo in svg

American Standard Portsmouth 7415.801 Series, Installation Instructions Manual, Page: 1 / 8

Share
Download
American Standard Portsmouth 7415.801 Series Installation Instructions Manual Download Page 1

M 9 6 5 015   R E V. 1. 7

Certified to comply with ANSI A112.18.1

Adjustable Wrench

 Screwdriver

Channel Locks

Recommended tools

Tubing Cutter

1

2

1

3

4

6

12

5

SLOT

Turn off hot and cold water

supplies before beginning.

CAUTION

Insert SPOUT 

(1)

 and CABLE CONNECTOR 

(12)

 through center hole, making sure

the SEAL WASHER 

(3) 

is properly seated in the SPOUT ESCUTCHEON 

(2)

.

Assemble RUBBER WASHER 

(4)

, BRASS WASHER 

(5)

 and LOCKNUT 

(6)

 onto SPOUT

SHANK 

(7)

 from under side of sink . Make sure SPOUT 

(1)

 is centered in the mounting

hole and the

 slot

 in the BRASS WASHER 

(5)

 faces toward the rear of the sink.

Tighten LOCKNUT 

(6)

 firmly. 

Fig. A.

1

1A

INSTALL SPOUT

INSTALL VALVE BODY

1

8

11

7

Fig.

 

A.

MOUNTING

SURFACE

Hand tighten LOCKNUT 

(11)

 to secure VALVE BODY 

(8)

.

Repeat above steps for opposite VALVE BODY 

(8A)

.

Install LOCKNUT 

(11) 

onto VALVE BODY 

(8)

.

From under side of mounting surface, install VALVE BODY 

(8)

 through valve

mounting holes. Threads of VALVE BODY 

(8)

 should extent at least 5/16

of a inch above mounting surface top. 

Fig. B.

 

Thread ADAPTER 

(10)

onto VALVE BODY 

(8)

 until snug against internal stop. If necessary, adjust

LOCKNUT 

(11)

.

8

11

Place RUBBER RING 

(9)

 into ADAPTER 

(10)

.

5/16'' MIN.

8A

Fig.

 

B.

7420.801

7420.821

Series

7415.801

7415.821

Series

Installation

Instructions

PORTSMOUTH™

Spread Lavatory Faucet

with Speed Connect™ Drain  

10

9

10

9

Congratulations on purchasing your

American Standard faucet with 

Speed Connect drain, a feature found 

onlyon American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

Heplful tips for removing your current drain can be found in the Troubleshooting section of these instructions.

To ensure that your installation proceeds smoothly-please read these instructions carefully 

before you begin.

74 2 0

74 15

Speed Connect Drain*

•  Fewer parts, installs in less time

•  Never needs adjustment

•  Guaranteed to seal properly the first time, every time.

Summary of Contents for Portsmouth 7415.801 Series









Reviews:

No comments