J61
BARRIER FREE
© 2008 AS America Inc.
146mm
(5-3/4)
41mm
(1-5/8)
425mm
(16-3/4)
127mm
(5)
216mm
(8-1/2)
203mm
(8)
*
216mm
(8-1/2)
FINISHED
FLOOR
SIDE PROFILE
(ADA)
1-1/4 O.D.
TAILPIECE
C/L OF SUPPLIES
AS REQUIRED
C/L OF (2) 13mm(1/2) DIA.
KNEE CONTACT GUARD
ANCHOR HOLES
13mm(1/2) DIA.
ANCHOR SCREW
HOLES
C/L OF 1-1/4
O.D. WASTE
C/L OF 16mm X 29mm
(5/8 X 1-1/8) ANCHOR
SLOTS
C/L OF 54mm(2-1/8 DIA.)
HOLES FOR
CONCEALED ARMS
197mm
(7-3/4)
102mm
(4)
152mm
(6)
102mm
(4)
83mm
(3-1/4)
(4) 25mm (1") DIA.
ACCESS HOLES
FOR CONC. ARMS
102mm
(4)
540mm
(21-1/4)
559mm
(22)
864mm
(34)
(FRONT
RIM)
743mm
(29-1/4)
254mm
(10) REF.
FINISHED
WALL
FINISHED
WALL
(2) 16mm (5/8") DIA.
ACCESS HOLES
FOR CONC. ARMS
406mm
(16)
REF.
*
267mm
(10-1/2)
165mm
(6-1/2)
89mm
(3-1/2)
44mm
(1-3/4)
MURRO™ UNIVERSAL DESIGN
WALL-HUNG LAVATORY
VITREOUS CHINA
MURRO™ UNIVERSAL DESIGN
WALL-HUNG LAVATORY
• Vitreous china
• Rear overflow
• Recessed self-draining deck
• For concealed arm or wall support
• Shown with optional vitreous china shroud/
knee contact guard 0059.020 available
❏
0954.000
Faucet holes on 102mm (4") Ctrs
(Illustrated)
❏
0954.023
Faucet holes on 102mm (4") Ctrs
• Extra right-hand hole
❏
0954.021
Faucet holes on 102mm (4") Ctrs
• Extra left-hand hole
❏
0958.000
Faucet holes on 203mm (8") Ctrs
❏
0955.000
Center hole only
❏
0955.023
Center hole
• Extra right-hand hole
❏
0955.021
Center hole
• Extra left-hand hole
Nominal Dimensions:
559mm (22") deep, 540mm (21-1/4") wide
Bowl sizes:
394mm (15-1/2") wide, 343mm (13-1/2")
front to back, 127mm (5") deep
❏
0059.020 Shroud/Knee Contact Guard
(Vitreous China) (Must be specified separately)
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.2 for Vitreous China Fixtures
To Be Specified:
❏
Color:
❏
White
❏
Bone
❏
Silver
❏
Optional Vitreous China Shroud/Knee
Contact guard: 0059.020
❏
Faucet*:
❏
Faucet Finish:
❏
Supplies:
❏
1-1/4" Trap:
❏
Nipple:
* See faucet section for additional models available
For Universal Design Options, top of rim may be mounted
at 813mm (32") from finished floor to meet ADA and ANSI
A117.1 requirements. Check local codes.
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDE-
LINES AND ANSI A117.1 ACCESSIBLE AND USABLE
BUILDINGS AND FACILITIES - CHECK LOCAL CODES.
Top of front rim mounted 864mm (34") from finished floor.
NOTES:
●
LOOSE KEY ANGLE STOPS, LESS WALL ESCUTCHEONS. SUPPLIES
REQUIRED.
*
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE
SUGGESTED.
SHROUD/KNEE CONTACT GUARD 0059.020 NOT INCLUDED AND MUST BE
ORDERED SEPARATELY.
■
SUITABLE FOR REINFORCEMENT ONLY, ACTUAL DIMENSIONS MUST
BE TAKEN FROM FIXTURE.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided pages.
SEE REVERSE FOR ADDITIONAL ROUGHING-IN
DIMENSIONS
Revised 5/06
