M 9 6 8 4 9 7 A
M 9 6 8 4 9 7 A
M 9 6 8 4 9 7 A
Turn on water supplies and check connections for leaks.
Remove AERATOR (1) with KEY (2) supplied.
Operate FAUCET by pressing down on HANDLE (3). Handle is
set for approximately 8 second operating cycle.
Replace AERATOR (1).
TEST INSTALLED FITTING
3
METERING
Pillar Tap Faucets
1340.105
1
2
3
PRESS HANDLE
DOWN TO OPERATE
Remove HANDLE (1). Refer to Step 4 for handle removal.
Remove ACTUATOR ASSEMBLY (2).
Remove WASHER (3). Pull out VALVE ASSEMBLY (4) and
FILTER SCREEN (5).
Inspect that VALVE ASSEMBLY (4), FILTER SCREEN (5) and
VALVE SEAT (6) are clean and free from debris. VALVE
ASSEMBLY (3) and FILTER SCREEN (5) can be cleaned with
soap and water.
Replace FILTER SCREEN (5) and VALVE ASSEMBLY (4). Place
WASHER (3) on top of VALVE ASSEMBLY (4). Thread VALVE
ACTUATOR (2) onto faucet. Torque VALVE ACTUATOR (2)
to 12-15 ft. lbs (15-20 Nm).
Replace HANDLE (1).
SERVICE
5
1
4
3
5
2
REMOVE
REPLACE
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A
COARSE SURFACE.
Remove HANDLE (1) by removing INDEX BUTTON (2)
and SET SCREW (3) with a 2.5mm hex wrench.
Pull off HANDLE (1).
To increase cycle time, turn the gray PLASTIC
ADJUSTING NUT (4) clockwise.
To decrease cycle time, turn the gray PLASTIC
ADJUSTING NUT (4) counter-clockwise.
Replace SET SCREW (3), INDEX BUTTON (2) and
HANDLE (1). Test faucet for proper operation and
cycle time.
TO ADJUST CYCLE TIME
4
1
2
3
4
TO INCREASE
CYCLE TIME
ROTATE
CLOCKWISE
TO DECREASE
CYCLE TIME
ROTATE
COUNTER-
CLOCKWISE
2.5mm HEX
WRENCH
6
PRODUCT NUMBER
M962393-YYY0A
AERATOR
*605P400.YYY
4" DECK PLATE
A911748-0070A
SEAL
M923290-0070A
24" SUPPLY
FLEX SUPPLY
M962390-YYYOA
HANDEL KIT
M962391-0070A
INDEX KIT
M952200-YYY0A
ACTUATOR UNIT
M913860-0070A
WASHER
M952210-0070A
VALVE
M952220-0070A
FILTER SCREEN
M962392-YYY0A
VALVE KIT
M961714-0070A
MOUNTING KIT
*605P800.YYY
8" DECK PLATE
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2005
CHROME
002
Replace the "YYY" with
appropriate finish code
Certified to comply with ANSI A112.18.1M
Turn off hot and cold water
supplies before beginning.
CAUTION
1
FAUCET INSTALLATION (With optional 4" Deck Plate)
SPOUT
RECESS
APPLY PUTTY
MOUNTING
SURFACE
COLD WATER
OR TEMPERED
WATER SUPPLY
3/8" COMPRESSION
PILLAR TAP FAUCET
Installation
Instructions
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Note: Faucet can be installed as single hole installation or
with (OPTIONAL) 4" or 8" DECK PLATES. 4" No. 605P400
& 8" No. 605P800 Deck Plates must be ordered separately.
METERING
1340.105
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter
Install SEAL (1) into base of FAUCET (2). Assemble Optional DECK PLATE (3), and PUTTY PLATE (4) to FAUCET BODY (2) with
SCREW (5). Apply a bead of putty to underside of PUTTY PLATE (3). Fig. 1a.
Insert FLEX HOSE (6) and SPOUT SHANK (7) through center hole of mounting surface. Fig. 1a.
Assemble "C" WASHER (8) and LOCKNUT (9) onto threads of SPOUT SHANK (7) from underside of mounting surface. Fig. 1b.
Align FAUCET (2) and tighten LOCKNUT (9). If installing DECK PLATE (3) hand tighten DECK PLATE SPIN NUTS (10) to secure
FAUCET (2) to mounting surface. Fig. 1b.
1
8
7
10
9
6
3
3
5
4
2
Fig. 1a
Fig. 1b
CONNECT WATER SUPPLY
2
Connect 3/8" compression coupling nut on fitting supply hose to
cold water supply or tempered water supply.
Note: Hose connection will not mate with Mechanical Mixing
Valve number 021943-0070A.
*DECK PLATES ARE NOT INCLUDED
WITH FITTING
