ASSEMBLY & INSTALLATION INSTRUCTIONS
- 1 -
- 2 -
In the United States:
American Standard Inc.
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty information
may also be obtained by calling the following
toll free number: (800) 442-1902
www.americanstandard-us.com
In Canada:
American Standard
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: (800) 387-0369
www.americanstandard.ca
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
www.americanstandard.com.mx
Recommended Tools & Materials
Roughing-in Dimensions
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2008
Hacksaw
Channel Locks
Adjustable Wrench
Tubing Cutter
Basin Wrench
Putty Knife
Tape
Measure
Plumbers’ Putty or
Caulking
Regular Screwdriver
Phillips Screwdriver
Drill
Level
Pipe Wrench
Generations 24" Washstand
9210.224.329
770002-100
770002-100
770002-100
770002-100
WASHSTAND INSTALLATION
Unpack unit carefully, taking care that bottom shelf does not drop and damage front legs (
see Figure 2
).
Provide suitable reinforcement for anchoring the washstand to the wall. Centerline of reinforcement should be 27-3/4"
up from the floor (
see Figure 1
).
Rough in supply lines and waste per rough-in dimensions.
The molding needs to be notched to seat the washstand flush against the wall.
Move the washstand into place and level with the adjustable glides on the bottom of the feet.
The glides can be adjusted outward up to 1" but it is recommended not to exceed 1/2" if possible.
Drill at least two 3/8" O.D. anchoring holes through the centerline of the rear stringer of the vessel stand, located 3/4"
down from the top of the table (
see Figure 2
).
Anchor the washstand to the wall through at least 2 of the anchoring holes in the rear of the washstand (
see Figure 2
).
Continue with installation appropriate for top and sink options chosen.
AMERICAN-STANDARD WOOD FURNITURE WARRANTY
If inspection of this American-Standard plumbing product, within one year after its initial purchase, confirms that it is defective in
materials or workmanship, American-Standard will repair or, at its option, exchange the product for a similar model. Variations in
actual wood color and finishes which may result from natural characteristics of the wood, such as grain patterns, mineral streaks
and the like, are not defects and are not covered by this warranty.
This warranty applies only to the original purchaser and installation of these products.
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the
purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before
installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty
maintenance, abuse, misuse, accident or other damages; if it was not installed in accordance with American-Standard’s
instructions; or if it has been modified in a manner inconsistent with the product as shipped by American-Standard.
American-Standard’s option to repair or exchange the product under this warranty does not cover any labor or other costs of
removal or installation, nor shall American-Standard be responsible for any other incidental or consequential damages
attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this
warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not
apply to you).
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or province to
province, in which case this warranty does not affect such statutory rights.
C/L of 2 x 6
Reinforcement
Finished
Floor
27-3/4"
(705mm)
FIGURE 1
-4-
REPLACEMENT PARTS LIST
9210.224.329 Generations 24" Washstand
ADJUSTABLE
LEVELLERS
(under each foot)
- 3 -
Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years.
To help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin.
Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.
To maintain the beauty of the finish, avoid placing the furniture in direct sunlight, as sunlight causes fading.
Also avoid extreme changes in temperature by arranging furniture away from radiators, heat and air vents,
and air conditioning units. Avoid placing furniture directly under windows.
22-1/2"
(570mm)
18"
(457mm)
33"
(838mm)
14-1/8"
(359mm)
16"
(406mm)
18"
(457mm)
TOWNSEND
SINK
SUPPLIES AS
REQUIRED
FINISHED
FLOOR
FINISHED
FLOOR
FINISHED
WALL
FINISHED
FLOOR
FINISHED
WALL
REAR STRINGER
WITH ANCHORING
HOLES TO SECURE
VANITY TO WALL
Care and Cleaning of Vanity
Clean the product by using soft, slightly damp cloth. Buff the product by using a soft dry cloth. Avoid using silicone cleaners and waxes.
Clean up excess water and spills immediately. Use a blotting rather than a wiping action. Water left over a long period of time will cause white
spots in the finish.
NOTE: Please note that some chemicals may damage the finish. Take care to avoid the following: iodine, hair dye, after shave lotion, shaving
cream, alcohol, perfume, Lestoil®, Lysol Tub and Tile Cleaner®, Lysol Spray Disinfectant®, Dow Disinfectant®, acetone, paint remover, Formula
409®, Tile-X®, and Nair®.
REPAIR PART NO.
DESCRIPTION
THREADER LEVELER (1 PER PACK) FOR WASHSTAND
730679-0070A
VANITY TOP
No top required for
Townsend Vanity Top (sink)
0555.104 Townsend Vanity Top (4" centers)
0555.108 Townsend Vanity Top (8" centers)
7005.201 Copeland Center Spread
7005.801 Copeland Wide Spread
RECOMMENDED SINKS
RECOMMENDED FAUCETS
1-1/4" O.D.
WASTE
FIGURE 2
ANCHORING
HOLES
IN REAR
STRINGER
[NOT SHOWN]
TOWNSEND VANITY TOP 0555.104/0555.108
INSTALLATION onto WASHSTAND…
Two people recommended for this installation
Mount the drain assembly (not included) on the sink. Be certain to apply
a bead of sealing putty on the underside of the drain (Part "A") in order to ensure
a watertight seal between the sink and drain. Remove excess putty after installing
the drain on the sink.
Apply a bead of silicone adhesive to the rim of the vanity. Place the top centered
left to right on the vanity and with the back edge of the top even with the rear of
the vanity. Apply a bead of silicone along the top back edge of the vanity top
and the wall. Clean up any excess silicone.
Connect the trap to the drain assembly hand tight to check alignment. It may be necessary
to cut off part of the tailpiece (area "B") or part horizontal leg of the trap (area "C").
Connect hot and cold supply lines to the shut off valves.
Tighten trap joints for watertight assembly.
A
B
C
Drawer pulls
out to access
Storage
Townsend Sink
Open Storage
33"
(838mm)
8"
(203mm)
2-1/2"
(64mm)
4"
(102mm)
