RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
SAVE FOR FUTURE USE
7 3 0 1 1 4 4 - 1 0 0 R e v . F
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE:
Pictures may not exactly define contour of china and components.
Model 2479.216 / 2479.516 / 2476.216 / 2476.516 / 2779.516
Model 2480.216 / 2480.516 / 2484.216 / 2484.516 / 2778.516 /
2566.216 Right Height™
FloWise™ DUAL FLUSH 2-PIECE TOILET
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
CLOSET
FLANGE
CLOSET
BOLTS
A
WAX RING
SEALANT
5
4
3
INSTALL WAX SEAL
Invert toilet on floor (cushion to
prevent damage), and install wax
ring evenly around waste flange
(horn), with tapered end of ring
facing toilet. Apply a thin bead of
sealant around toilet base.
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange
so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers
marked "THIS SIDE UP"
must
face up!
CLOSET
BOLT
NUT
TAPERED
WASHER
BOLT
CAP
FLANGE
INSTALL CLOSET BOLTS
Install closet bolts in flange channel,
turn 90°, and slide into place 6"
(152mm) apart and parallel to wall.
TEMPORARILY set toilet in place.
Place tapered washer and nuts onto
the bolts as shown in Step 5. Mark bolt
length needed for bolt cap clearance.
Remove toilet. Precut the bolts to
length by twisting the nut onto the bolt
past the cut mark, then cutting the bolt
to the desired length with a hacksaw.
Unscrew the nut to repair the threads.
Re-install bolts in flange.
!
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line.
NOTE:
If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level
before
new toilet is installed!
2
1
ROUGHING-IN DIMENSIONS:
305mm
(12)
794mm
(31-1/4)
197mm
(7-3/4)
C/L OF OUTLET
FINISHED WALL
PUSH
BUTTON
41mm ± 6mm
(1-5/8±1/4)
375mm
(14-3/4)
C/L
470mm
(18-1/2)
C/L OF SEAT POST HOLES
140mm (5-1/2 CENTRES)
121mm
(4-3/4)
FINISHED
FLOOR
765mm
(30-1/8)
251mm
(9-7/8)
114mm
(4-1/2)
432mm
(17)
203mm
(8)
371mm
(14-5/8)
111mm
(4-3/8)
SUPPLY
AS
REQ'D
397mm
(15-5/8)
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a I n c .
© A S A m e r i c a I n c . 2 0 0 8
REMOVE OLD TOILET
305mm
(12)
794mm
(31-1/4)
197mm
(7-3/4)
C/L OF OUTLET
FINISHED WALL
PUSH
BUTTON
41mm ± 6mm
(1-5/8±1/4)
448mm
(17-5/8)
C/L
470mm
(18-1/2)
C/L OF SEAT POST HOLES
140mm (5-1/2 CENTRES)
121mm
(4-3/4)
FINISHED
FLOOR
829m
m
(32-5/8)
265mm
(10-3/8)
114mm
(4-1/2)
432mm
(17)
203mm
(8)
370mm
(14-5/8)
111mm
(4-3/8)
*SUPPLY
AS
REQ'D
410mm
(16-1/8)
Models: 2479.216 / 2479.516 /
2476.216 / 2476.516 / 2779.516
Models: 2480.216 / 2480.516 / 2484.216 / 2484.516 /
2778.516 / 2566.216 Right Height™
Certified by
IAPMO R&T