7301050-100 Rev.C
7301050-100 Rev.C
7301050-100 Rev.C
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 2 0 0 7
ASSEMBLY & INSTALLATION
INSTRUCTIONS
Cascada 30" Vanity
9437.200
Newbern Vanity Top
7820.800
- 2 -
- 3 -
- 1 -
In the United States:
American Standard Inc.
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty information
may also be obtained by calling the following
toll free number: (800) 442-1902
In Canada:
American Standard
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: (800) 387-0369
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Recommended Tools & Materials
Roughing-in Dimensions
Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years.
To help insure that the installation process will proceed smoothly, please read these instructions carefully before you
begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.
Adjustable Wrench
Channel Locks
Phillips Screwdriver
Putty Knife
Regular Screwdriver
Drill
Saber Saw
Level
Basin Wrench
Plumbers' Putty or
Caulking
Tubing Cutter
10'
Tape
Measure
Hacksaw
Pipe Wrench
™
Care and Cleaning of Vanity
Dust the vanity frequently with a clean, soft, dry, lint-free cloth, as well as polish it on a regular basis. Clean the surface by rubbing in the direction
of the grain. Use polishes that contain detergents, emulsifiers and mineral oil. Avoid using silicone cleaners and waxes.
Clean up excess water and spills immediately. Use a blotting rather than a wiping action. Water left over a long period of time will cause white
spots in the finish.
NOTE: Please note that some chemicals may damage the finish. Take care to avoid the following: iodine, hair dye, after shave lotion, shaving
cream, alcohol, perfume, Lestoil®, Lysol Tub and Tile Cleaner®, Lysol Spray Disinfectant®, Dow Disinfectant®, acetone, paint remover, Formula
409®, Tile-X®, and Nair®.
AMERICAN-STANDARD GRANITE/MARBLE TABLE TOP WARRANTY
If inspection of this American-Standard plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship,
American-Standard will repair or, at its option, exchange the product for a similar model. Variations in shading, veining, and texture which may result from
natural characteristics of stone and as such are not defects and are not covered by this warranty.
This warranty applies only to the original purchaser and installation of these products.
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should
check with a local building or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse,
accident or other damages; if it was not installed in accordance with American-Standard’s instructions; or if it has been modified in a manner inconsistent
with the product as shipped by American-Standard.
American-Standard’s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor
shall American-Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a
defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied
warranties, so this exclusion may not apply to you).
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or province to province, in which case this
warranty does not affect such statutory rights.
AMERICAN-STANDARD WOOD FURNITURE WARRANTY
If inspection of this American-Standard plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship,
American-Standard will repair or, at its option, exchange the product for a similar model. Variations in actual wood color and finishes which may result from
natural characteristics of the wood, such as grain patterns, mineral streaks and the like, are not defects and are not covered by this warranty.
This warranty applies only to the original purchaser and installation of these products.
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should
check with a local building or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse,
accident or other damages; if it was not installed in accordance with American-Standard’s instructions; or if it has been modified in a manner inconsistent
with the product as shipped by American-Standard.
American-Standard’s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor
shall American-Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a
defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied
warranties, so this exclusion may not apply to you).
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or province to province, in which case this
warranty does not affect such statutory rights.
21"
533mm
30"
762mm
34"
864mm
22-3/4"
578mm
26-3/4"
679mm
6"
(152mm)
1-1/4" O.D.
WASTE
SUPPLIES
AS REQ'D
FINISHED FLOOR
To maintain the beauty of the finish, avoid placing the furniture in direct sunlight, as sunlight causes fading. Also avoid
extreme changes in temperature by arranging furniture away from radiators, heat and air vents, and air conditioning
units. Avoid placing furniture directly under windows.
REPAIR PART NO.
7301063-0070A
7301062-0070A
7301067-XXX0A
730674-0070A
DESCRIPTION
BRUSHED NICKEL PULL
DRAWER GLIDE
DRAWER FRONT
THREADED LEVELLER
NOTE: PLEASE SPECIFY FINISH
XXX - 334 Maple
XXX - 310 Tobacco
C/L of 2 x 6
Reinforcement
Finished
Floor
27-3/4"
Provide suitable reinforcement required for anchoring the vanity to the wall. Centerline of reinforcement should be 27-3/4" up from the
floor (see Figure 1).
Open vanity drawers. Remove screws from inside drawers and pull drawers off drawer glides. (see Figure 2).
If molding is present, it will need to be notched to set the vanity flush against the wall. (see Figure 3).
Rough in supply lines and waste per rough in dimensions.
NOTE:
If current supply lines are greater than 6" on center,
they may interfere with cutout in rear of vanity or vanity shelf.
Move the vanity into place and level with the adjustable
glides on the bottom of the feet. The glides can be adjusted
outward up to 3/4" but it is recommended not to exceed 1/2"
if possible. Anchor it to the wall through at least 2 of the
anchoring holes in the rear of the vanity (see Figure 4).
Installing the Newbern Top…
Two people recommended for this installation
Mount the drain assembly (not included) on the sink. Be certain to apply
a bead of sealing putty on the underside of the drain (Part "A") in order to
ensure a watertight seal between the sink and drain. Remove excess
putty after installing the drain on the sink.
Apply a bead of silicone adhesive to the rim of the vanity. Place the
Newbern top centered left to right on the vanity and with the back edge of
the top even with the rear of the vanity. Clean up any excess silicone.
Place top back on vanity and, connect the trap to the drain assembly
hand tight to check alignment. It may be necessary to cut off part of the
tailpiece (area "B") or part horizontal leg of the trap (area "C").
Connect hot and cold supply lines to the shut off valves. Tighten trap
joints for watertight assembly.
A
B
C
VANITY INSTALLATION
MOLDING
ADJUSTABLE GLIDES
(LOCATED UNDER
EACH FOOT)
FIGURE 1
FIGURE 3
21
(533mm)
C/L
27-1/2"
578mm
Using a 3/8" O.D. drill, drill 3 anchoring
holes, equally spaced, in back support of
vanity (see Figure 4).
Continue with installation appropriate for
top and sink options chosen.
FIGURE 4
ANCHORING
HOLES (3)
FIGURE 2
DRAWER
REMOVE
SCREWS
