INSTALLATION INSTRUCTIONS
752864-100 Rev. C
© American Standard Inc. 2003
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
CADENZA ELITE™
WHIRLPOOL
6060E SERIES
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
T H A N K Y O U . . .
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately.
After inspection and during installation, protect the bath from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit and check for leaks.
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,
motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and
enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead
(required for recess installations).
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
List of Optional Components (not included):
• Flex-Jet Pulse Jet Kit*
• Flex-Jet Soft Jet Kit*
• Apron Kit*
• Tile Bead Kit*
List of Required Components (not included):
• Drain* • Bath Filler*
* see your Home Depot Retailer
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 15 amp GFI & 20 amp
GFI Outlet
• Cement, Plaster,
Grout
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
GENERAL SPECIFICATIONS FOR 6060E WHIRLPOOL
WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP
76-3/4 x 65-3/8 x 21-1/2 In. (1949 x 1661 x 546mm)
105 Lbs. (48 Kg.)
822 Lbs. (370 Kg.)
86 Gal. (326 L)
71 Gal. (269 L)
45 x 40 In. (1143 x 1016mm)
49 x 43 In. (1245 x 1092mm)
15-3/8 In. (391mm)
24 Lbs./Sq.Ft. (114 Kgs./Sq.m)
41.7
68.4
2.1 HP, 14.4 AMPS,120V.
E-Z INSTALL WHIRLPOOL HEATER
12.0 AMPS,120V.
1949mm
(76-3/4 REF.)
546mm
(21-1/2)
ROUGH FLOOR
495mm
(19-1/2)
1384m
m
(54-1/2)
1605mm
(63-3/16)
975mm
(38-3/8)
1661mm
(65-3/8)
346mm
(13-5/8)
SEAT AREA
254mm
(10)
114mm
(4-1/2)
PROVIDE ACCESS TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
NOTE: APRON ASSEMBLY WILL PROVIDE REQUIRED
ACCESS FOR SERVICING
51mm
(2)
89mm
(3-1/2)
C/L OF OVERFLOW
LEVELING STRINGER
NOT FOR SUPPORT
PUMP
178mm x 381mm
(7 x 15) CUTOUT
C/L OF
DRAIN
143mm
(5-5/8)
OUTLINE OF
CUTOUT
C/L
ON/OFF SWITCH
83mm
(3-1/4)
1-1/2 N.P.T. THREAD
1-1/2 O.D. TAILPIECE
38mm
(1-1/2)
INTEGRAL FEET
SUPPORT
RECOMMENDED FITTING
LOCATION 64 X 381mm (2-1/2 X 15)
●
■
E-Z INSTALL WHIRLPOOL
HEATER
