Page 1 of 2
11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633
©2021 American Lighting, Inc. REV2125 www.AmericanLighting.com
S RGBTW
REMOTE
3V
INSTALLATION INSTRUCTIONS
SPKPL-CTRL-W-RGBTW
SAFETY INFORMATION
• Read all installation instructions before beginning; if not qualified, do not attempt
installation. Contact a qualified electrician.
• To reduce the risk of fire, electric shock, or injury to persons, pay close attention
to this manual and stay within its guidelines when using this product. Save these
instructions for future use.
• This product is rated IP54 and suitable for indoor use in dry locations.
• Do not submerge in liquids nor use the product in the vicinity of standing water or
other liquids, or where water can accumulate.
• Do not use if there is any damage to the product; inspect periodically.
• Do not install in tanks or enclosures of any kinds.
• This product utilizes Bluetooth® wireless technology and a 3V CR2032 battery;
only replace with same battery type. Please dispose of batteries properly.
Batteries are not a toy! If swallowed, contact local emergency services
immediately.
These products may represent a possible shock or fire
hazard if improperly installed or attached in any way.
Products should be installed in accordance with these
instructions, current electrical codes, and/or the current
National Electric Code (NEC).
This product utilizes Bluetooth wireless technology
and a 3V CR2032 battery; only replace with same
battery type. Batteries are not a toy!
WARNING
WARNING
USING THE REMOTE CONTROLLER (See Figure 1):
Do not
remove protective film from battery compartment until ready to
use. This remote includes a 3V CR2032 battery, only replace with
the same type battery. Please dispose of old batteries properly.
USING REMOTE WITH S SMART LIGHTING APP:
Add the remote to the app by selecting “Add Device”, then press
and hold the On + Off buttons together for 3 seconds to enter
configuration mode. Follow the app instructions to finish binding
the remote. Within the app, select the remote device icon from
the list of synced devices, then to add devices to be controlled by
the remote. The remote can be added to specific rooms as well.
DISTANCE OF CONTROL CAPABILITY:
25 meters (approx. 80ft)
RESET THE REMOTE CONTROLLER:
Press and hold the Off and
Scene buttons together for 5 seconds.
USING THE S SMART LIGHTING APP:
Please follow
the S Smart Lighting App guide.
FIGURE 1
Press Once for On
Press Once for Off
Cycle through
preset RGB
colors
10 settings
Press & Hold to
Save a Scene
Press Once for
Scene Recall
Adjust color
temperature
2700K-6000K
8 preset steps
Press & Hold for
Brightness Up
Press & Hold for
Brightness Down
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.