WARNING: These products may present a possible shock
or fire hazard if improperly installed or attached in any
way. Products should be installed in accordance with the
owners manual, current electrical codes and/or the
current National Electric Code (NEC).
IMPORTANT
The following instructions are provided to assure safe
installation and operation of LED Mini Swivel Series.
Please read carefully before connecting or installing this
product.
1. The LED Mini Swivels are a safe low voltage lighting
system that are suitable for indoor locations only.
2. Do not mount or support these fixtures in a manner
that can cut the outer jacket or damage wire insulation.
3. Always make sure power is disconnected from the LED
fixtures before cutting, mounting, attaching terminal
block, attaching end cap or modifying in any way.
4. Do not exceed the maximum capacity of the 350mA
DC power supply used for any series configuration.
SPECIFICATIONS - Please see other side for details
BEFORE YOU START
•
Always make sure the power supply (LED driver) is
disconnected from the power source before wiring
LED Swivel lights.
• Determine the number and locations of fixtures your
application will require. There are multiple power
connection configurations and accessories that allow
many installation options. See Figures 1-3 for examples.
Prior to installation, determine the best configuration for
each installation.
OPTICAL LENS OPTIONS FOR LMV AND LMS
The LED Mini Visor (LMV) and the LED Mini Swivel (LMS)
are shipped with an optical lens with a 25˚ beam angle
installed. An additional optical lens accessory with an
80˚ beam angle is included with each LMV and LMS
fixture. To replace the lens, turn the lens frame counter-
clockwise to remove. Replace the lens by placing it
upright on the LED cover and replacing the lens frame
over the top. Turn the lens frame clockwise until snug.
FOR HARDWIRE INSTALLATIONS
1. Check that the male plastic connector of each LED fixture is in
operable condition. If in operable condition, insert male plastic
connector into an open female port of the power connector. See
Figures 2 and 3.
2. When powering only one fixture, it is necessary to insert an end
cap, LED-END-350, into any open ports to complete the series
wiring. When powering light sets, every port of each power
connector must be connected to an end cap, another power
connector or a light. The whole set will not light if any port
remains empty. See Figures 2 and 3.
CONNECTING TO POWER SUPPLY
Use a 350mA power supply as recommended by the factory. Use
of any other power supply will void the warranty. Make sure the
power source is disconnected before making any
connections.
1. When connecting to LED-DR12-350 or LED-DR18-350 power
supplies, plug the plastic connector directly into the mating port
on the secondary side of the power supply. See Figures 2 and 3.
2. When using LED-DR18-350D power supply, cut off the plastic
connector of the last power connector in the series and wire to
the secondary side of the driver, matching polarity. Connect solid
red power connector lead to power supply lead marked positive.
Black/red striped power connector lead goes to negative supply
lead.
3. Connect 120V AC power to the primary side matching polarity
and turn on power.
MOUNTING LED MINI SWIVEL SERIES
1. Always make sure power is disconnected before modifying,
mounting or installing a series of LED Mini Swivel Lights.
2. Drill a 1-7/8” hole for LMS or LMV fixtures; or 2-3/4” hole for
LMS-3 fixtures.
3. Open steel spring clips.
4. Insert LED Mini Swivel into hole.
5. Make sure that the fixture’s lead wire is not in contact with
sharp objects.
6. Maximum wattage per series is dependent upon the capacity
of the power supply. Add the number of lights and respective
wattages to assure you do not exceed the maximum wattage.
LED MINI SWIVEL SERIES
Installation instructions for LMS, LMV, LMS-3, LMS-3KIT, LMV-3KIT and LMS-3-3KIT series fixtures (CONTINUED FROM OTHER SIDE)
RV-1125
www.americanlighting.com
Figure 1
LED-CON2-350
LED-CON3-350
LED-CON6-350HW
LED-CON6-350
Figure 2
Figure 3
LED-CON2-350 connectors
*
This plastic connector can plug directly into the female
port on LED-DR12-250 or LED-DR18-350 drivers.
LED-CON3-350
*